Endress+Hauser Liquiline CM44x Heartbeat pH and Conductivity
Sensorconditie en kalibratiehistorie voor pH en geleidbaarheid op Liquiline CM44x.
De Endress+Hauser Liquiline CM44x is een meerkanaals transmitter voor vloeistofanalyse. Deze Modbus RTU-template leest de Heartbeat Monitoring-gegevens van maximaal acht pH- en acht geleidbaarheidssensoren, zodat je sensorconditie en kalibratie in ModbusCloud volgt.
- Protocol
- Modbus RTU
- Aansluiting
- RS485, 19200 baud
- Registers
- 440, alleen lezen
- Merk
- Endress+Hauser
- Belangrijke uitlezingen
- NAMUR NE107-status · Diagnosecode · Steilheid en nulpunt · Glasimpedantie · Celconstante · Bedrijfsuren
- Ondersteunde modellen
- Liquiline CM442 · Liquiline CM444 · Liquiline CM448 · Liquiline CM44P · Liquiline CM44R
- Laatst bijgewerkt
Registers (440)
440 lezen, 0 schrijven
| Naam | Eenheid | Toegang | Adres (Verborgen tot je je e-mailadres invult) | Functie (verborgen) | Type (verborgen) |
|---|---|---|---|---|---|
| pH 1 Diagnosis Time | Lezen | ||||
| pH 1 Manufacturing Date | Lezen | ||||
| pH 1 Initial Operation Date | Lezen | ||||
| pH 1 Last Calibration Date | Lezen | ||||
| pH 1 Slope | Lezen | ||||
| pH 1 Slope Change Since Last Calibration | Lezen | ||||
| pH 1 Zero point | Lezen | ||||
| pH 1 Zero Point Change Since Last Calibration | Lezen | ||||
| pH 1 Glass impedance | Ω | Lezen | |||
| pH 1 Reference impedance | Ω | Lezen | |||
| pH 1 Temperature offset | K | Lezen | |||
| pH 1 Leakage current | A | Lezen | |||
| pH 1 Min. measured value | Lezen | ||||
| pH 1 Min. measured temperature value | °C | Lezen | |||
| pH 1 Max. measured value | Lezen | ||||
| pH 1 Max. measured temperature value | °C | Lezen | |||
| pH 1 Operating hours of connected sensor | s | Lezen | |||
| pH 1 Operating time >80°C | s | Lezen | |||
| pH 1 Operating time >100°C | s | Lezen | |||
| pH 1 Operating time <-300mV (pH) | s | Lezen | |||
| pH 1 Operating time >300mV (pH) | s | Lezen | |||
| pH 1 Number of sterilization cycles | Lezen | ||||
| pH 1 Number of clean in place cycles | Lezen | ||||
| pH 1 Diagnosis Code | Lezen | ||||
| pH 1 NAMUR NE107 Status | Lezen | ||||
| pH 1 Selected sensor type | Lezen | ||||
| pH 1 Temperature Slope (2-point Calibration) | Lezen | ||||
| pH 1 The pH value of buffer 1 | pH | Lezen | |||
| pH 1 The pH value of buffer 2 | pH | Lezen | |||
| pH 1 The pH value of buffer 3 | pH | Lezen | |||
| pH 2 Diagnosis Time | Lezen | ||||
| pH 2 Manufacturing Date | Lezen | ||||
| pH 2 Initial Operation Date | Lezen | ||||
| pH 2 Last Calibration Date | Lezen | ||||
| pH 2 Slope | Lezen | ||||
| pH 2 Slope Change Since Last Calibration | Lezen | ||||
| pH 2 Zero point | Lezen | ||||
| pH 2 Zero Point Change Since Last Calibration | Lezen | ||||
| pH 2 Glass impedance | Ω | Lezen | |||
| pH 2 Reference impedance | Ω | Lezen | |||
| pH 2 Temperature offset | K | Lezen | |||
| pH 2 Leakage current | A | Lezen | |||
| pH 2 Min. measured value | Lezen | ||||
| pH 2 Min. measured temperature value | °C | Lezen | |||
| pH 2 Max. measured value | Lezen | ||||
| pH 2 Max. measured temperature value | °C | Lezen | |||
| pH 2 Operating hours of connected sensor | s | Lezen | |||
| pH 2 Operating time >80°C | s | Lezen | |||
| pH 2 Operating time >100°C | s | Lezen | |||
| pH 2 Operating time <-300mV (pH) | s | Lezen | |||
| pH 2 Operating time >300mV (pH) | s | Lezen | |||
| pH 2 Number of sterilization cycles | Lezen | ||||
| pH 2 Number of clean in place cycles | Lezen | ||||
| pH 2 Diagnosis Code | Lezen | ||||
| pH 2 NAMUR NE107 Status | Lezen | ||||
| pH 2 Selected sensor type | Lezen | ||||
| pH 2 Temperature Slope (2-point Calibration) | Lezen | ||||
| pH 2 The pH value of buffer 1 | pH | Lezen | |||
| pH 2 The pH value of buffer 2 | pH | Lezen | |||
| pH 2 The pH value of buffer 3 | pH | Lezen | |||
| pH 3 Diagnosis Time | Lezen | ||||
| pH 3 Manufacturing Date | Lezen | ||||
| pH 3 Initial Operation Date | Lezen | ||||
| pH 3 Last Calibration Date | Lezen | ||||
| pH 3 Slope | Lezen | ||||
| pH 3 Slope Change Since Last Calibration | Lezen | ||||
| pH 3 Zero point | Lezen | ||||
| pH 3 Zero Point Change Since Last Calibration | Lezen | ||||
| pH 3 Glass impedance | Ω | Lezen | |||
| pH 3 Reference impedance | Ω | Lezen | |||
| pH 3 Temperature offset | K | Lezen | |||
| pH 3 Leakage current | A | Lezen | |||
| pH 3 Min. measured value | Lezen | ||||
| pH 3 Min. measured temperature value | °C | Lezen | |||
| pH 3 Max. measured value | Lezen | ||||
| pH 3 Max. measured temperature value | °C | Lezen | |||
| pH 3 Operating hours of connected sensor | s | Lezen | |||
| pH 3 Operating time >80°C | s | Lezen | |||
| pH 3 Operating time >100°C | s | Lezen | |||
| pH 3 Operating time <-300mV (pH) | s | Lezen | |||
| pH 3 Operating time >300mV (pH) | s | Lezen | |||
| pH 3 Number of sterilization cycles | Lezen | ||||
| pH 3 Number of clean in place cycles | Lezen | ||||
| pH 3 Diagnosis Code | Lezen | ||||
| pH 3 NAMUR NE107 Status | Lezen | ||||
| pH 3 Selected sensor type | Lezen | ||||
| pH 3 Temperature Slope (2-point Calibration) | Lezen | ||||
| pH 3 The pH value of buffer 1 | pH | Lezen | |||
| pH 3 The pH value of buffer 2 | pH | Lezen | |||
| pH 3 The pH value of buffer 3 | pH | Lezen | |||
| pH 4 Diagnosis Time | Lezen | ||||
| pH 4 Manufacturing Date | Lezen | ||||
| pH 4 Initial Operation Date | Lezen | ||||
| pH 4 Last Calibration Date | Lezen | ||||
| pH 4 Slope | Lezen | ||||
| pH 4 Slope Change Since Last Calibration | Lezen | ||||
| pH 4 Zero point | Lezen | ||||
| pH 4 Zero Point Change Since Last Calibration | Lezen | ||||
| pH 4 Glass impedance | Ω | Lezen | |||
| pH 4 Reference impedance | Ω | Lezen | |||
| pH 4 Temperature offset | K | Lezen | |||
| pH 4 Leakage current | A | Lezen | |||
| pH 4 Min. measured value | Lezen | ||||
| pH 4 Min. measured temperature value | °C | Lezen | |||
| pH 4 Max. measured value | Lezen | ||||
| pH 4 Max. measured temperature value | °C | Lezen | |||
| pH 4 Operating hours of connected sensor | s | Lezen | |||
| pH 4 Operating time >80°C | s | Lezen | |||
| pH 4 Operating time >100°C | s | Lezen | |||
| pH 4 Operating time <-300mV (pH) | s | Lezen | |||
| pH 4 Operating time >300mV (pH) | s | Lezen | |||
| pH 4 Number of sterilization cycles | Lezen | ||||
| pH 4 Number of clean in place cycles | Lezen | ||||
| pH 4 Diagnosis Code | Lezen | ||||
| pH 4 NAMUR NE107 Status | Lezen | ||||
| pH 4 Selected sensor type | Lezen | ||||
| pH 4 Temperature Slope (2-point Calibration) | Lezen | ||||
| pH 4 The pH value of buffer 1 | pH | Lezen | |||
| pH 4 The pH value of buffer 2 | pH | Lezen | |||
| pH 4 The pH value of buffer 3 | pH | Lezen | |||
| pH 5 Diagnosis Time | Lezen | ||||
| pH 5 Manufacturing Date | Lezen | ||||
| pH 5 Initial Operation Date | Lezen | ||||
| pH 5 Last Calibration Date | Lezen | ||||
| pH 5 Slope | Lezen | ||||
| pH 5 Slope Change Since Last Calibration | Lezen | ||||
| pH 5 Zero point | Lezen | ||||
| pH 5 Zero Point Change Since Last Calibration | Lezen | ||||
| pH 5 Glass impedance | Ω | Lezen | |||
| pH 5 Reference impedance | Ω | Lezen | |||
| pH 5 Temperature offset | K | Lezen | |||
| pH 5 Leakage current | A | Lezen | |||
| pH 5 Min. measured value | Lezen | ||||
| pH 5 Min. measured temperature value | °C | Lezen | |||
| pH 5 Max. measured value | Lezen | ||||
| pH 5 Max. measured temperature value | °C | Lezen | |||
| pH 5 Operating hours of connected sensor | s | Lezen | |||
| pH 5 Operating time >80°C | s | Lezen | |||
| pH 5 Operating time >100°C | s | Lezen | |||
| pH 5 Operating time <-300mV (pH) | s | Lezen | |||
| pH 5 Operating time >300mV (pH) | s | Lezen | |||
| pH 5 Number of sterilization cycles | Lezen | ||||
| pH 5 Number of clean in place cycles | Lezen | ||||
| pH 5 Diagnosis Code | Lezen | ||||
| pH 5 NAMUR NE107 Status | Lezen | ||||
| pH 5 Selected sensor type | Lezen | ||||
| pH 5 Temperature Slope (2-point Calibration) | Lezen | ||||
| pH 5 The pH value of buffer 1 | pH | Lezen | |||
| pH 5 The pH value of buffer 2 | pH | Lezen | |||
| pH 5 The pH value of buffer 3 | pH | Lezen | |||
| pH 6 Diagnosis Time | Lezen | ||||
| pH 6 Manufacturing Date | Lezen | ||||
| pH 6 Initial Operation Date | Lezen | ||||
| pH 6 Last Calibration Date | Lezen | ||||
| pH 6 Slope | Lezen | ||||
| pH 6 Slope Change Since Last Calibration | Lezen | ||||
| pH 6 Zero point | Lezen | ||||
| pH 6 Zero Point Change Since Last Calibration | Lezen | ||||
| pH 6 Glass impedance | Ω | Lezen | |||
| pH 6 Reference impedance | Ω | Lezen | |||
| pH 6 Temperature offset | K | Lezen | |||
| pH 6 Leakage current | A | Lezen | |||
| pH 6 Min. measured value | Lezen | ||||
| pH 6 Min. measured temperature value | °C | Lezen | |||
| pH 6 Max. measured value | Lezen | ||||
| pH 6 Max. measured temperature value | °C | Lezen | |||
| pH 6 Operating hours of connected sensor | s | Lezen | |||
| pH 6 Operating time >80°C | s | Lezen | |||
| pH 6 Operating time >100°C | s | Lezen | |||
| pH 6 Operating time <-300mV (pH) | s | Lezen | |||
| pH 6 Operating time >300mV (pH) | s | Lezen | |||
| pH 6 Number of sterilization cycles | Lezen | ||||
| pH 6 Number of clean in place cycles | Lezen | ||||
| pH 6 Diagnosis Code | Lezen | ||||
| pH 6 NAMUR NE107 Status | Lezen | ||||
| pH 6 Selected sensor type | Lezen | ||||
| pH 6 Temperature Slope (2-point Calibration) | Lezen | ||||
| pH 6 The pH value of buffer 1 | pH | Lezen | |||
| pH 6 The pH value of buffer 2 | pH | Lezen | |||
| pH 6 The pH value of buffer 3 | pH | Lezen | |||
| pH 7 Diagnosis Time | Lezen | ||||
| pH 7 Manufacturing Date | Lezen | ||||
| pH 7 Initial Operation Date | Lezen | ||||
| pH 7 Last Calibration Date | Lezen | ||||
| pH 7 Slope | Lezen | ||||
| pH 7 Slope Change Since Last Calibration | Lezen | ||||
| pH 7 Zero point | Lezen | ||||
| pH 7 Zero Point Change Since Last Calibration | Lezen | ||||
| pH 7 Glass impedance | Ω | Lezen | |||
| pH 7 Reference impedance | Ω | Lezen | |||
| pH 7 Temperature offset | K | Lezen | |||
| pH 7 Leakage current | A | Lezen | |||
| pH 7 Min. measured value | Lezen | ||||
| pH 7 Min. measured temperature value | °C | Lezen | |||
| pH 7 Max. measured value | Lezen | ||||
| pH 7 Max. measured temperature value | °C | Lezen | |||
| pH 7 Operating hours of connected sensor | s | Lezen | |||
| pH 7 Operating time >80°C | s | Lezen | |||
| pH 7 Operating time >100°C | s | Lezen | |||
| pH 7 Operating time <-300mV (pH) | s | Lezen | |||
| pH 7 Operating time >300mV (pH) | s | Lezen | |||
| pH 7 Number of sterilization cycles | Lezen | ||||
| pH 7 Number of clean in place cycles | Lezen | ||||
| pH 7 Diagnosis Code | Lezen | ||||
| pH 7 NAMUR NE107 Status | Lezen | ||||
| pH 7 Selected sensor type | Lezen | ||||
| pH 7 Temperature Slope (2-point Calibration) | Lezen | ||||
| pH 7 The pH value of buffer 1 | pH | Lezen | |||
| pH 7 The pH value of buffer 2 | pH | Lezen | |||
| pH 7 The pH value of buffer 3 | pH | Lezen | |||
| pH 8 Diagnosis Time | Lezen | ||||
| pH 8 Manufacturing Date | Lezen | ||||
| pH 8 Initial Operation Date | Lezen | ||||
| pH 8 Last Calibration Date | Lezen | ||||
| pH 8 Slope | Lezen | ||||
| pH 8 Slope Change Since Last Calibration | Lezen | ||||
| pH 8 Zero point | Lezen | ||||
| pH 8 Zero Point Change Since Last Calibration | Lezen | ||||
| pH 8 Glass impedance | Ω | Lezen | |||
| pH 8 Reference impedance | Ω | Lezen | |||
| pH 8 Temperature offset | K | Lezen | |||
| pH 8 Leakage current | A | Lezen | |||
| pH 8 Min. measured value | Lezen | ||||
| pH 8 Min. measured temperature value | °C | Lezen | |||
| pH 8 Max. measured value | Lezen | ||||
| pH 8 Max. measured temperature value | °C | Lezen | |||
| pH 8 Operating hours of connected sensor | s | Lezen | |||
| pH 8 Operating time >80°C | s | Lezen | |||
| pH 8 Operating time >100°C | s | Lezen | |||
| pH 8 Operating time <-300mV (pH) | s | Lezen | |||
| pH 8 Operating time >300mV (pH) | s | Lezen | |||
| pH 8 Number of sterilization cycles | Lezen | ||||
| pH 8 Number of clean in place cycles | Lezen | ||||
| pH 8 Diagnosis Code | Lezen | ||||
| pH 8 NAMUR NE107 Status | Lezen | ||||
| pH 8 Selected sensor type | Lezen | ||||
| pH 8 Temperature Slope (2-point Calibration) | Lezen | ||||
| pH 8 The pH value of buffer 1 | pH | Lezen | |||
| pH 8 The pH value of buffer 2 | pH | Lezen | |||
| pH 8 The pH value of buffer 3 | pH | Lezen | |||
| Cond. 1 Diagnosis Time | Lezen | ||||
| Cond. 1 Manufacturing Date | Lezen | ||||
| Cond. 1 Initial Operation Date | Lezen | ||||
| Cond. 1 Last Slope Calibration Date | Lezen | ||||
| Cond. 1 Cell constant | Lezen | ||||
| Cond. 1 Cell Constant Change Since Last Calibration | Lezen | ||||
| Cond. 1 Temperature offset | K | Lezen | |||
| Cond. 1 Min. measured value | Lezen | ||||
| Cond. 1 Min. measured temperature value | °C | Lezen | |||
| Cond. 1 Max. measured value | Lezen | ||||
| Cond. 1 Max. measured temperature value | °C | Lezen | |||
| Cond. 1 Operating hours of connected sensor | s | Lezen | |||
| Cond. 1 Raw value | Lezen | ||||
| Cond. 1 Operating time >80°C | s | Lezen | |||
| Cond. 1 Operating time >100°C (Cond 4pol) | s | Lezen | |||
| Cond. 1 Operating time >120°C (cond.) | s | Lezen | |||
| Cond. 1 Operating time >125°C (ind.) | s | Lezen | |||
| Cond. 1 Operating time >140°C (Cond 2pol) | s | Lezen | |||
| Cond. 1 Operating time >150°C (Cond i, Cond 4pol) | s | Lezen | |||
| Cond. 1 Operating time <100nS (cond.) | s | Lezen | |||
| Cond. 1 Number of sterilization cycles | Lezen | ||||
| Cond. 1 Number of clean in place cycles | Lezen | ||||
| Cond. 1 Diagnosis Code | Lezen | ||||
| Cond. 1 NAMUR NE107 Status | Lezen | ||||
| Cond. 1 Selected sensor type | Lezen | ||||
| Cond. 2 Diagnosis Time | Lezen | ||||
| Cond. 2 Manufacturing Date | Lezen | ||||
| Cond. 2 Initial Operation Date | Lezen | ||||
| Cond. 2 Last Slope Calibration Date | Lezen | ||||
| Cond. 2 Cell constant | Lezen | ||||
| Cond. 2 Cell Constant Change Since Last Calibration | Lezen | ||||
| Cond. 2 Temperature offset | K | Lezen | |||
| Cond. 2 Min. measured value | Lezen | ||||
| Cond. 2 Min. measured temperature value | °C | Lezen | |||
| Cond. 2 Max. measured value | Lezen | ||||
| Cond. 2 Max. measured temperature value | °C | Lezen | |||
| Cond. 2 Operating hours of connected sensor | s | Lezen | |||
| Cond. 2 Raw value | Lezen | ||||
| Cond. 2 Operating time >80°C | s | Lezen | |||
| Cond. 2 Operating time >100°C (Cond 4pol) | s | Lezen | |||
| Cond. 2 Operating time >120°C (cond.) | s | Lezen | |||
| Cond. 2 Operating time >125°C (ind.) | s | Lezen | |||
| Cond. 2 Operating time >140°C (Cond 2pol) | s | Lezen | |||
| Cond. 2 Operating time >150°C (Cond i, Cond 4pol) | s | Lezen | |||
| Cond. 2 Operating time <100nS (cond.) | s | Lezen | |||
| Cond. 2 Number of sterilization cycles | Lezen | ||||
| Cond. 2 Number of clean in place cycles | Lezen | ||||
| Cond. 2 Diagnosis Code | Lezen | ||||
| Cond. 2 NAMUR NE107 Status | Lezen | ||||
| Cond. 2 Selected sensor type | Lezen | ||||
| Cond. 3 Diagnosis Time | Lezen | ||||
| Cond. 3 Manufacturing Date | Lezen | ||||
| Cond. 3 Initial Operation Date | Lezen | ||||
| Cond. 3 Last Slope Calibration Date | Lezen | ||||
| Cond. 3 Cell constant | Lezen | ||||
| Cond. 3 Cell Constant Change Since Last Calibration | Lezen | ||||
| Cond. 3 Temperature offset | K | Lezen | |||
| Cond. 3 Min. measured value | Lezen | ||||
| Cond. 3 Min. measured temperature value | °C | Lezen | |||
| Cond. 3 Max. measured value | Lezen | ||||
| Cond. 3 Max. measured temperature value | °C | Lezen | |||
| Cond. 3 Operating hours of connected sensor | s | Lezen | |||
| Cond. 3 Raw value | Lezen | ||||
| Cond. 3 Operating time >80°C | s | Lezen | |||
| Cond. 3 Operating time >100°C (Cond 4pol) | s | Lezen | |||
| Cond. 3 Operating time >120°C (cond.) | s | Lezen | |||
| Cond. 3 Operating time >125°C (ind.) | s | Lezen | |||
| Cond. 3 Operating time >140°C (Cond 2pol) | s | Lezen | |||
| Cond. 3 Operating time >150°C (Cond i, Cond 4pol) | s | Lezen | |||
| Cond. 3 Operating time <100nS (cond.) | s | Lezen | |||
| Cond. 3 Number of sterilization cycles | Lezen | ||||
| Cond. 3 Number of clean in place cycles | Lezen | ||||
| Cond. 3 Diagnosis Code | Lezen | ||||
| Cond. 3 NAMUR NE107 Status | Lezen | ||||
| Cond. 3 Selected sensor type | Lezen | ||||
| Cond. 4 Diagnosis Time | Lezen | ||||
| Cond. 4 Manufacturing Date | Lezen | ||||
| Cond. 4 Initial Operation Date | Lezen | ||||
| Cond. 4 Last Slope Calibration Date | Lezen | ||||
| Cond. 4 Cell constant | Lezen | ||||
| Cond. 4 Cell Constant Change Since Last Calibration | Lezen | ||||
| Cond. 4 Temperature offset | K | Lezen | |||
| Cond. 4 Min. measured value | Lezen | ||||
| Cond. 4 Min. measured temperature value | °C | Lezen | |||
| Cond. 4 Max. measured value | Lezen | ||||
| Cond. 4 Max. measured temperature value | °C | Lezen | |||
| Cond. 4 Operating hours of connected sensor | s | Lezen | |||
| Cond. 4 Raw value | Lezen | ||||
| Cond. 4 Operating time >80°C | s | Lezen | |||
| Cond. 4 Operating time >100°C (Cond 4pol) | s | Lezen | |||
| Cond. 4 Operating time >120°C (cond.) | s | Lezen | |||
| Cond. 4 Operating time >125°C (ind.) | s | Lezen | |||
| Cond. 4 Operating time >140°C (Cond 2pol) | s | Lezen | |||
| Cond. 4 Operating time >150°C (Cond i, Cond 4pol) | s | Lezen | |||
| Cond. 4 Operating time <100nS (cond.) | s | Lezen | |||
| Cond. 4 Number of sterilization cycles | Lezen | ||||
| Cond. 4 Number of clean in place cycles | Lezen | ||||
| Cond. 4 Diagnosis Code | Lezen | ||||
| Cond. 4 NAMUR NE107 Status | Lezen | ||||
| Cond. 4 Selected sensor type | Lezen | ||||
| Cond. 5 Diagnosis Time | Lezen | ||||
| Cond. 5 Manufacturing Date | Lezen | ||||
| Cond. 5 Initial Operation Date | Lezen | ||||
| Cond. 5 Last Slope Calibration Date | Lezen | ||||
| Cond. 5 Cell constant | Lezen | ||||
| Cond. 5 Cell Constant Change Since Last Calibration | Lezen | ||||
| Cond. 5 Temperature offset | K | Lezen | |||
| Cond. 5 Min. measured value | Lezen | ||||
| Cond. 5 Min. measured temperature value | °C | Lezen | |||
| Cond. 5 Max. measured value | Lezen | ||||
| Cond. 5 Max. measured temperature value | °C | Lezen | |||
| Cond. 5 Operating hours of connected sensor | s | Lezen | |||
| Cond. 5 Raw value | Lezen | ||||
| Cond. 5 Operating time >80°C | s | Lezen | |||
| Cond. 5 Operating time >100°C (Cond 4pol) | s | Lezen | |||
| Cond. 5 Operating time >120°C (cond.) | s | Lezen | |||
| Cond. 5 Operating time >125°C (ind.) | s | Lezen | |||
| Cond. 5 Operating time >140°C (Cond 2pol) | s | Lezen | |||
| Cond. 5 Operating time >150°C (Cond i, Cond 4pol) | s | Lezen | |||
| Cond. 5 Operating time <100nS (cond.) | s | Lezen | |||
| Cond. 5 Number of sterilization cycles | Lezen | ||||
| Cond. 5 Number of clean in place cycles | Lezen | ||||
| Cond. 5 Diagnosis Code | Lezen | ||||
| Cond. 5 NAMUR NE107 Status | Lezen | ||||
| Cond. 5 Selected sensor type | Lezen | ||||
| Cond. 6 Diagnosis Time | Lezen | ||||
| Cond. 6 Manufacturing Date | Lezen | ||||
| Cond. 6 Initial Operation Date | Lezen | ||||
| Cond. 6 Last Slope Calibration Date | Lezen | ||||
| Cond. 6 Cell constant | Lezen | ||||
| Cond. 6 Cell Constant Change Since Last Calibration | Lezen | ||||
| Cond. 6 Temperature offset | K | Lezen | |||
| Cond. 6 Min. measured value | Lezen | ||||
| Cond. 6 Min. measured temperature value | °C | Lezen | |||
| Cond. 6 Max. measured value | Lezen | ||||
| Cond. 6 Max. measured temperature value | °C | Lezen | |||
| Cond. 6 Operating hours of connected sensor | s | Lezen | |||
| Cond. 6 Raw value | Lezen | ||||
| Cond. 6 Operating time >80°C | s | Lezen | |||
| Cond. 6 Operating time >100°C (Cond 4pol) | s | Lezen | |||
| Cond. 6 Operating time >120°C (cond.) | s | Lezen | |||
| Cond. 6 Operating time >125°C (ind.) | s | Lezen | |||
| Cond. 6 Operating time >140°C (Cond 2pol) | s | Lezen | |||
| Cond. 6 Operating time >150°C (Cond i, Cond 4pol) | s | Lezen | |||
| Cond. 6 Operating time <100nS (cond.) | s | Lezen | |||
| Cond. 6 Number of sterilization cycles | Lezen | ||||
| Cond. 6 Number of clean in place cycles | Lezen | ||||
| Cond. 6 Diagnosis Code | Lezen | ||||
| Cond. 6 NAMUR NE107 Status | Lezen | ||||
| Cond. 6 Selected sensor type | Lezen | ||||
| Cond. 7 Diagnosis Time | Lezen | ||||
| Cond. 7 Manufacturing Date | Lezen | ||||
| Cond. 7 Initial Operation Date | Lezen | ||||
| Cond. 7 Last Slope Calibration Date | Lezen | ||||
| Cond. 7 Cell constant | Lezen | ||||
| Cond. 7 Cell Constant Change Since Last Calibration | Lezen | ||||
| Cond. 7 Temperature offset | K | Lezen | |||
| Cond. 7 Min. measured value | Lezen | ||||
| Cond. 7 Min. measured temperature value | °C | Lezen | |||
| Cond. 7 Max. measured value | Lezen | ||||
| Cond. 7 Max. measured temperature value | °C | Lezen | |||
| Cond. 7 Operating hours of connected sensor | s | Lezen | |||
| Cond. 7 Raw value | Lezen | ||||
| Cond. 7 Operating time >80°C | s | Lezen | |||
| Cond. 7 Operating time >100°C (Cond 4pol) | s | Lezen | |||
| Cond. 7 Operating time >120°C (cond.) | s | Lezen | |||
| Cond. 7 Operating time >125°C (ind.) | s | Lezen | |||
| Cond. 7 Operating time >140°C (Cond 2pol) | s | Lezen | |||
| Cond. 7 Operating time >150°C (Cond i, Cond 4pol) | s | Lezen | |||
| Cond. 7 Operating time <100nS (cond.) | s | Lezen | |||
| Cond. 7 Number of sterilization cycles | Lezen | ||||
| Cond. 7 Number of clean in place cycles | Lezen | ||||
| Cond. 7 Diagnosis Code | Lezen | ||||
| Cond. 7 NAMUR NE107 Status | Lezen | ||||
| Cond. 7 Selected sensor type | Lezen | ||||
| Cond. 8 Diagnosis Time | Lezen | ||||
| Cond. 8 Manufacturing Date | Lezen | ||||
| Cond. 8 Initial Operation Date | Lezen | ||||
| Cond. 8 Last Slope Calibration Date | Lezen | ||||
| Cond. 8 Cell constant | Lezen | ||||
| Cond. 8 Cell Constant Change Since Last Calibration | Lezen | ||||
| Cond. 8 Temperature offset | K | Lezen | |||
| Cond. 8 Min. measured value | Lezen | ||||
| Cond. 8 Min. measured temperature value | °C | Lezen | |||
| Cond. 8 Max. measured value | Lezen | ||||
| Cond. 8 Max. measured temperature value | °C | Lezen | |||
| Cond. 8 Operating hours of connected sensor | s | Lezen | |||
| Cond. 8 Raw value | Lezen | ||||
| Cond. 8 Operating time >80°C | s | Lezen | |||
| Cond. 8 Operating time >100°C (Cond 4pol) | s | Lezen | |||
| Cond. 8 Operating time >120°C (cond.) | s | Lezen | |||
| Cond. 8 Operating time >125°C (ind.) | s | Lezen | |||
| Cond. 8 Operating time >140°C (Cond 2pol) | s | Lezen | |||
| Cond. 8 Operating time >150°C (Cond i, Cond 4pol) | s | Lezen | |||
| Cond. 8 Operating time <100nS (cond.) | s | Lezen | |||
| Cond. 8 Number of sterilization cycles | Lezen | ||||
| Cond. 8 Number of clean in place cycles | Lezen | ||||
| Cond. 8 Diagnosis Code | Lezen | ||||
| Cond. 8 NAMUR NE107 Status | Lezen | ||||
| Cond. 8 Selected sensor type | Lezen |
Registers laden…
Stuur jouw apparatenlijst
Staat een apparaat niet in de bibliotheek, dan maken we de template gratis zodra we de registers hebben.
Gebruikstoepassingen
- Krijg een e-mail als de NAMUR-status van een pH-sensor van OK naar onderhoud nodig gaat.
- Volg steilheid en nulpunt van elke pH-sensor tussen kalibraties om veroudering te zien.
- Plan sensorvervanging op basis van bedrijfsuren en de tijd boven 80 °C.
- Controleer op een dashboard wanneer elke geleidbaarheidssensor voor het laatst is gekalibreerd.
Installatie
Activeer Heartbeat Monitoring op de Liquiline CM44x met de activeringscode van Endress+Hauser.
Sluit de RS485-poort van de Liquiline aan op de ModbusCloud Gateway en noteer busadres, baudrate en pariteit (af fabriek 247, 19.200 baud, even).
Voeg in ModbusCloud een Modbus apparaat toe met die instellingen en importeer deze template.
Verwijder de kanaalblokken zonder pH- of geleidbaarheidssensor en controleer of het geselecteerde sensortype van de overige kanalen klopt.
Veelvoorkomende aandachtspunten
Alle Heartbeat-registers geven 0. Hoe komt dat?
Heartbeat Monitoring heeft een activeringscode nodig. Zonder code antwoordt de Liquiline op elk register in dit blok met 0.
Float-waarden kloppen niet. Wat is er mis?
De template gebruikt de fabrieksvolgorde 1-0-3-2 (CDAB). Is de parameter Byte order op de Liquiline gewijzigd, zet hem terug of pas de byte order van de float-registers aan.
Hoe lees ik de datumregisters?
Datums gebruiken het E+H DATETIME-formaat met milliseconden, minuten, uren, dag, maand en jaar verpakt in acht bytes. De template leest ze als één ruw 64-bit getal.
Kan ik met deze template instellingen wijzigen?
Nee. Heartbeat-registers zijn inputregisters en alleen leesbaar. Kalibratie en instellingen doe je op de Liquiline zelf of via de hoofdtemplate Liquiline CM44x.
Meer Endress+Hauser-templates
Zelf zien hoe het werkt?
