Endress+Hauser Liquiline CM44x Heartbeat Oxygen and Disinfection
Sensorgezondheid en kalibratiehistorie van zuurstof- en chloorsensoren op een Liquiline CM44x.
De Endress+Hauser Liquiline CM44x is een meerkanaals transmitter die opgeloste zuurstof, chloor en andere waterparameters meet in waterbehandeling, tuinbouw en industrie. Deze Modbus RTU-template leest de Heartbeat Monitoring-gegevens van maximaal acht zuurstof- en acht desinfectiesensoren, zodat je sensorgezondheid en kalibratie volgt in ModbusCloud.
- Protocol
- Modbus RTU
- Aansluiting
- RS485, 19200 baud
- Registers
- 832, alleen lezen
- Merk
- Endress+Hauser
- Belangrijke uitlezingen
- NAMUR NE107-status · Diagnosecode · Helling en nulpunt · Kalibratiedata · Bedrijfsuren · Bedrijfsuren van de cap
- Ondersteunde modellen
- Liquiline CM442 · Liquiline CM444 · Liquiline CM448 · Liquiline CM44P · Liquiline CM44R
- Laatst bijgewerkt
Registers (832)
832 lezen, 0 schrijven
| Naam | Eenheid | Toegang | Adres (Verborgen tot je je e-mailadres invult) | Functie (verborgen) | Type (verborgen) |
|---|---|---|---|---|---|
| Disinfection 1 Diagnosis Time | Lezen | ||||
| Disinfection 1 Manufacturing Date | Lezen | ||||
| Disinfection 1 Initial Operation Date | Lezen | ||||
| Disinfection 1 Last Slope Calibration Date | Lezen | ||||
| Disinfection 1 Last Zero Point Calibration Date | Lezen | ||||
| Disinfection 1 Slope | Lezen | ||||
| Disinfection 1 Slope Change Since Last Calibration | Lezen | ||||
| Disinfection 1 Zero Point | Lezen | ||||
| Disinfection 1 Zero Point Change Since Last Calibration | Lezen | ||||
| Disinfection 1 Temperature Offset | K | Lezen | |||
| Disinfection 1 Electrical Charge | Lezen | ||||
| Disinfection 1 Min Measured Value | Lezen | ||||
| Disinfection 1 Min Measured Temperature | °C | Lezen | |||
| Disinfection 1 Max Measured Value | Lezen | ||||
| Disinfection 1 Max Measured Temperature | °C | Lezen | |||
| Disinfection 1 Operating Hours | s | Lezen | |||
| Disinfection 1 Operating Time Above 15 C | s | Lezen | |||
| Disinfection 1 Operating Time Above 30 C | s | Lezen | |||
| Disinfection 1 Operating Time Below -20 nA | s | Lezen | |||
| Disinfection 1 Operating Time Below -100 nA | s | Lezen | |||
| Disinfection 1 Sensor Cap Calibrations | Lezen | ||||
| Disinfection 1 Diagnosis Code | Lezen | ||||
| Disinfection 1 NAMUR NE107 Status | Lezen | ||||
| Disinfection 1 Selected Sensor Type | Lezen | ||||
| Disinfection 1 Number Of Calibrations | Lezen | ||||
| Disinfection 1 Number Of Sterilizations | Lezen | ||||
| Disinfection 1 Clean In Place Cycles | Lezen | ||||
| Disinfection 1 Number Of Autoclavings | Lezen | ||||
| Disinfection 1 Cap Sterilization Cycles | Lezen | ||||
| Disinfection 1 Cap Clean In Place Cycles | Lezen | ||||
| Disinfection 1 Cap Autoclavings | Lezen | ||||
| Disinfection 1 Electrolyte Capacity | Lezen | ||||
| Disinfection 1 Operating Hours Above T3 | s | Lezen | |||
| Disinfection 1 Cap Operating Hours | s | Lezen | |||
| Disinfection 1 Cap Operating Hours Above T1 | s | Lezen | |||
| Disinfection 1 Cap Operating Hours Above T2 | s | Lezen | |||
| Disinfection 1 Cap Operating Hours Above T3 | s | Lezen | |||
| Disinfection 1 Cap Operating Hours Above T4 | s | Lezen | |||
| Disinfection 1 Cap Operating Hours Above T5 | s | Lezen | |||
| Disinfection 1 Sensor Element | Lezen | ||||
| Disinfection 1 Temperature Threshold T1 | Lezen | ||||
| Disinfection 1 Temperature Threshold T2 | Lezen | ||||
| Disinfection 1 Temperature Threshold T3 | Lezen | ||||
| Disinfection 1 Current Threshold T4 | A | Lezen | |||
| Disinfection 1 Current Threshold T5 | A | Lezen | |||
| Disinfection 2 Diagnosis Time | Lezen | ||||
| Disinfection 2 Manufacturing Date | Lezen | ||||
| Disinfection 2 Initial Operation Date | Lezen | ||||
| Disinfection 2 Last Slope Calibration Date | Lezen | ||||
| Disinfection 2 Last Zero Point Calibration Date | Lezen | ||||
| Disinfection 2 Slope | Lezen | ||||
| Disinfection 2 Slope Change Since Last Calibration | Lezen | ||||
| Disinfection 2 Zero Point | Lezen | ||||
| Disinfection 2 Zero Point Change Since Last Calibration | Lezen | ||||
| Disinfection 2 Temperature Offset | K | Lezen | |||
| Disinfection 2 Electrical Charge | Lezen | ||||
| Disinfection 2 Min Measured Value | Lezen | ||||
| Disinfection 2 Min Measured Temperature | °C | Lezen | |||
| Disinfection 2 Max Measured Value | Lezen | ||||
| Disinfection 2 Max Measured Temperature | °C | Lezen | |||
| Disinfection 2 Operating Hours | s | Lezen | |||
| Disinfection 2 Operating Time Above 15 C | s | Lezen | |||
| Disinfection 2 Operating Time Above 30 C | s | Lezen | |||
| Disinfection 2 Operating Time Below -20 nA | s | Lezen | |||
| Disinfection 2 Operating Time Below -100 nA | s | Lezen | |||
| Disinfection 2 Sensor Cap Calibrations | Lezen | ||||
| Disinfection 2 Diagnosis Code | Lezen | ||||
| Disinfection 2 NAMUR NE107 Status | Lezen | ||||
| Disinfection 2 Selected Sensor Type | Lezen | ||||
| Disinfection 2 Number Of Calibrations | Lezen | ||||
| Disinfection 2 Number Of Sterilizations | Lezen | ||||
| Disinfection 2 Clean In Place Cycles | Lezen | ||||
| Disinfection 2 Number Of Autoclavings | Lezen | ||||
| Disinfection 2 Cap Sterilization Cycles | Lezen | ||||
| Disinfection 2 Cap Clean In Place Cycles | Lezen | ||||
| Disinfection 2 Cap Autoclavings | Lezen | ||||
| Disinfection 2 Electrolyte Capacity | Lezen | ||||
| Disinfection 2 Operating Hours Above T3 | s | Lezen | |||
| Disinfection 2 Cap Operating Hours | s | Lezen | |||
| Disinfection 2 Cap Operating Hours Above T1 | s | Lezen | |||
| Disinfection 2 Cap Operating Hours Above T2 | s | Lezen | |||
| Disinfection 2 Cap Operating Hours Above T3 | s | Lezen | |||
| Disinfection 2 Cap Operating Hours Above T4 | s | Lezen | |||
| Disinfection 2 Cap Operating Hours Above T5 | s | Lezen | |||
| Disinfection 2 Sensor Element | Lezen | ||||
| Disinfection 2 Temperature Threshold T1 | Lezen | ||||
| Disinfection 2 Temperature Threshold T2 | Lezen | ||||
| Disinfection 2 Temperature Threshold T3 | Lezen | ||||
| Disinfection 2 Current Threshold T4 | A | Lezen | |||
| Disinfection 2 Current Threshold T5 | A | Lezen | |||
| Disinfection 3 Diagnosis Time | Lezen | ||||
| Disinfection 3 Manufacturing Date | Lezen | ||||
| Disinfection 3 Initial Operation Date | Lezen | ||||
| Disinfection 3 Last Slope Calibration Date | Lezen | ||||
| Disinfection 3 Last Zero Point Calibration Date | Lezen | ||||
| Disinfection 3 Slope | Lezen | ||||
| Disinfection 3 Slope Change Since Last Calibration | Lezen | ||||
| Disinfection 3 Zero Point | Lezen | ||||
| Disinfection 3 Zero Point Change Since Last Calibration | Lezen | ||||
| Disinfection 3 Temperature Offset | K | Lezen | |||
| Disinfection 3 Electrical Charge | Lezen | ||||
| Disinfection 3 Min Measured Value | Lezen | ||||
| Disinfection 3 Min Measured Temperature | °C | Lezen | |||
| Disinfection 3 Max Measured Value | Lezen | ||||
| Disinfection 3 Max Measured Temperature | °C | Lezen | |||
| Disinfection 3 Operating Hours | s | Lezen | |||
| Disinfection 3 Operating Time Above 15 C | s | Lezen | |||
| Disinfection 3 Operating Time Above 30 C | s | Lezen | |||
| Disinfection 3 Operating Time Below -20 nA | s | Lezen | |||
| Disinfection 3 Operating Time Below -100 nA | s | Lezen | |||
| Disinfection 3 Sensor Cap Calibrations | Lezen | ||||
| Disinfection 3 Diagnosis Code | Lezen | ||||
| Disinfection 3 NAMUR NE107 Status | Lezen | ||||
| Disinfection 3 Selected Sensor Type | Lezen | ||||
| Disinfection 3 Number Of Calibrations | Lezen | ||||
| Disinfection 3 Number Of Sterilizations | Lezen | ||||
| Disinfection 3 Clean In Place Cycles | Lezen | ||||
| Disinfection 3 Number Of Autoclavings | Lezen | ||||
| Disinfection 3 Cap Sterilization Cycles | Lezen | ||||
| Disinfection 3 Cap Clean In Place Cycles | Lezen | ||||
| Disinfection 3 Cap Autoclavings | Lezen | ||||
| Disinfection 3 Electrolyte Capacity | Lezen | ||||
| Disinfection 3 Operating Hours Above T3 | s | Lezen | |||
| Disinfection 3 Cap Operating Hours | s | Lezen | |||
| Disinfection 3 Cap Operating Hours Above T1 | s | Lezen | |||
| Disinfection 3 Cap Operating Hours Above T2 | s | Lezen | |||
| Disinfection 3 Cap Operating Hours Above T3 | s | Lezen | |||
| Disinfection 3 Cap Operating Hours Above T4 | s | Lezen | |||
| Disinfection 3 Cap Operating Hours Above T5 | s | Lezen | |||
| Disinfection 3 Sensor Element | Lezen | ||||
| Disinfection 3 Temperature Threshold T1 | Lezen | ||||
| Disinfection 3 Temperature Threshold T2 | Lezen | ||||
| Disinfection 3 Temperature Threshold T3 | Lezen | ||||
| Disinfection 3 Current Threshold T4 | A | Lezen | |||
| Disinfection 3 Current Threshold T5 | A | Lezen | |||
| Disinfection 4 Diagnosis Time | Lezen | ||||
| Disinfection 4 Manufacturing Date | Lezen | ||||
| Disinfection 4 Initial Operation Date | Lezen | ||||
| Disinfection 4 Last Slope Calibration Date | Lezen | ||||
| Disinfection 4 Last Zero Point Calibration Date | Lezen | ||||
| Disinfection 4 Slope | Lezen | ||||
| Disinfection 4 Slope Change Since Last Calibration | Lezen | ||||
| Disinfection 4 Zero Point | Lezen | ||||
| Disinfection 4 Zero Point Change Since Last Calibration | Lezen | ||||
| Disinfection 4 Temperature Offset | K | Lezen | |||
| Disinfection 4 Electrical Charge | Lezen | ||||
| Disinfection 4 Min Measured Value | Lezen | ||||
| Disinfection 4 Min Measured Temperature | °C | Lezen | |||
| Disinfection 4 Max Measured Value | Lezen | ||||
| Disinfection 4 Max Measured Temperature | °C | Lezen | |||
| Disinfection 4 Operating Hours | s | Lezen | |||
| Disinfection 4 Operating Time Above 15 C | s | Lezen | |||
| Disinfection 4 Operating Time Above 30 C | s | Lezen | |||
| Disinfection 4 Operating Time Below -20 nA | s | Lezen | |||
| Disinfection 4 Operating Time Below -100 nA | s | Lezen | |||
| Disinfection 4 Sensor Cap Calibrations | Lezen | ||||
| Disinfection 4 Diagnosis Code | Lezen | ||||
| Disinfection 4 NAMUR NE107 Status | Lezen | ||||
| Disinfection 4 Selected Sensor Type | Lezen | ||||
| Disinfection 4 Number Of Calibrations | Lezen | ||||
| Disinfection 4 Number Of Sterilizations | Lezen | ||||
| Disinfection 4 Clean In Place Cycles | Lezen | ||||
| Disinfection 4 Number Of Autoclavings | Lezen | ||||
| Disinfection 4 Cap Sterilization Cycles | Lezen | ||||
| Disinfection 4 Cap Clean In Place Cycles | Lezen | ||||
| Disinfection 4 Cap Autoclavings | Lezen | ||||
| Disinfection 4 Electrolyte Capacity | Lezen | ||||
| Disinfection 4 Operating Hours Above T3 | s | Lezen | |||
| Disinfection 4 Cap Operating Hours | s | Lezen | |||
| Disinfection 4 Cap Operating Hours Above T1 | s | Lezen | |||
| Disinfection 4 Cap Operating Hours Above T2 | s | Lezen | |||
| Disinfection 4 Cap Operating Hours Above T3 | s | Lezen | |||
| Disinfection 4 Cap Operating Hours Above T4 | s | Lezen | |||
| Disinfection 4 Cap Operating Hours Above T5 | s | Lezen | |||
| Disinfection 4 Sensor Element | Lezen | ||||
| Disinfection 4 Temperature Threshold T1 | Lezen | ||||
| Disinfection 4 Temperature Threshold T2 | Lezen | ||||
| Disinfection 4 Temperature Threshold T3 | Lezen | ||||
| Disinfection 4 Current Threshold T4 | A | Lezen | |||
| Disinfection 4 Current Threshold T5 | A | Lezen | |||
| Disinfection 5 Diagnosis Time | Lezen | ||||
| Disinfection 5 Manufacturing Date | Lezen | ||||
| Disinfection 5 Initial Operation Date | Lezen | ||||
| Disinfection 5 Last Slope Calibration Date | Lezen | ||||
| Disinfection 5 Last Zero Point Calibration Date | Lezen | ||||
| Disinfection 5 Slope | Lezen | ||||
| Disinfection 5 Slope Change Since Last Calibration | Lezen | ||||
| Disinfection 5 Zero Point | Lezen | ||||
| Disinfection 5 Zero Point Change Since Last Calibration | Lezen | ||||
| Disinfection 5 Temperature Offset | K | Lezen | |||
| Disinfection 5 Electrical Charge | Lezen | ||||
| Disinfection 5 Min Measured Value | Lezen | ||||
| Disinfection 5 Min Measured Temperature | °C | Lezen | |||
| Disinfection 5 Max Measured Value | Lezen | ||||
| Disinfection 5 Max Measured Temperature | °C | Lezen | |||
| Disinfection 5 Operating Hours | s | Lezen | |||
| Disinfection 5 Operating Time Above 15 C | s | Lezen | |||
| Disinfection 5 Operating Time Above 30 C | s | Lezen | |||
| Disinfection 5 Operating Time Below -20 nA | s | Lezen | |||
| Disinfection 5 Operating Time Below -100 nA | s | Lezen | |||
| Disinfection 5 Sensor Cap Calibrations | Lezen | ||||
| Disinfection 5 Diagnosis Code | Lezen | ||||
| Disinfection 5 NAMUR NE107 Status | Lezen | ||||
| Disinfection 5 Selected Sensor Type | Lezen | ||||
| Disinfection 5 Number Of Calibrations | Lezen | ||||
| Disinfection 5 Number Of Sterilizations | Lezen | ||||
| Disinfection 5 Clean In Place Cycles | Lezen | ||||
| Disinfection 5 Number Of Autoclavings | Lezen | ||||
| Disinfection 5 Cap Sterilization Cycles | Lezen | ||||
| Disinfection 5 Cap Clean In Place Cycles | Lezen | ||||
| Disinfection 5 Cap Autoclavings | Lezen | ||||
| Disinfection 5 Electrolyte Capacity | Lezen | ||||
| Disinfection 5 Operating Hours Above T3 | s | Lezen | |||
| Disinfection 5 Cap Operating Hours | s | Lezen | |||
| Disinfection 5 Cap Operating Hours Above T1 | s | Lezen | |||
| Disinfection 5 Cap Operating Hours Above T2 | s | Lezen | |||
| Disinfection 5 Cap Operating Hours Above T3 | s | Lezen | |||
| Disinfection 5 Cap Operating Hours Above T4 | s | Lezen | |||
| Disinfection 5 Cap Operating Hours Above T5 | s | Lezen | |||
| Disinfection 5 Sensor Element | Lezen | ||||
| Disinfection 5 Temperature Threshold T1 | Lezen | ||||
| Disinfection 5 Temperature Threshold T2 | Lezen | ||||
| Disinfection 5 Temperature Threshold T3 | Lezen | ||||
| Disinfection 5 Current Threshold T4 | A | Lezen | |||
| Disinfection 5 Current Threshold T5 | A | Lezen | |||
| Disinfection 6 Diagnosis Time | Lezen | ||||
| Disinfection 6 Manufacturing Date | Lezen | ||||
| Disinfection 6 Initial Operation Date | Lezen | ||||
| Disinfection 6 Last Slope Calibration Date | Lezen | ||||
| Disinfection 6 Last Zero Point Calibration Date | Lezen | ||||
| Disinfection 6 Slope | Lezen | ||||
| Disinfection 6 Slope Change Since Last Calibration | Lezen | ||||
| Disinfection 6 Zero Point | Lezen | ||||
| Disinfection 6 Zero Point Change Since Last Calibration | Lezen | ||||
| Disinfection 6 Temperature Offset | K | Lezen | |||
| Disinfection 6 Electrical Charge | Lezen | ||||
| Disinfection 6 Min Measured Value | Lezen | ||||
| Disinfection 6 Min Measured Temperature | °C | Lezen | |||
| Disinfection 6 Max Measured Value | Lezen | ||||
| Disinfection 6 Max Measured Temperature | °C | Lezen | |||
| Disinfection 6 Operating Hours | s | Lezen | |||
| Disinfection 6 Operating Time Above 15 C | s | Lezen | |||
| Disinfection 6 Operating Time Above 30 C | s | Lezen | |||
| Disinfection 6 Operating Time Below -20 nA | s | Lezen | |||
| Disinfection 6 Operating Time Below -100 nA | s | Lezen | |||
| Disinfection 6 Sensor Cap Calibrations | Lezen | ||||
| Disinfection 6 Diagnosis Code | Lezen | ||||
| Disinfection 6 NAMUR NE107 Status | Lezen | ||||
| Disinfection 6 Selected Sensor Type | Lezen | ||||
| Disinfection 6 Number Of Calibrations | Lezen | ||||
| Disinfection 6 Number Of Sterilizations | Lezen | ||||
| Disinfection 6 Clean In Place Cycles | Lezen | ||||
| Disinfection 6 Number Of Autoclavings | Lezen | ||||
| Disinfection 6 Cap Sterilization Cycles | Lezen | ||||
| Disinfection 6 Cap Clean In Place Cycles | Lezen | ||||
| Disinfection 6 Cap Autoclavings | Lezen | ||||
| Disinfection 6 Electrolyte Capacity | Lezen | ||||
| Disinfection 6 Operating Hours Above T3 | s | Lezen | |||
| Disinfection 6 Cap Operating Hours | s | Lezen | |||
| Disinfection 6 Cap Operating Hours Above T1 | s | Lezen | |||
| Disinfection 6 Cap Operating Hours Above T2 | s | Lezen | |||
| Disinfection 6 Cap Operating Hours Above T3 | s | Lezen | |||
| Disinfection 6 Cap Operating Hours Above T4 | s | Lezen | |||
| Disinfection 6 Cap Operating Hours Above T5 | s | Lezen | |||
| Disinfection 6 Sensor Element | Lezen | ||||
| Disinfection 6 Temperature Threshold T1 | Lezen | ||||
| Disinfection 6 Temperature Threshold T2 | Lezen | ||||
| Disinfection 6 Temperature Threshold T3 | Lezen | ||||
| Disinfection 6 Current Threshold T4 | A | Lezen | |||
| Disinfection 6 Current Threshold T5 | A | Lezen | |||
| Disinfection 7 Diagnosis Time | Lezen | ||||
| Disinfection 7 Manufacturing Date | Lezen | ||||
| Disinfection 7 Initial Operation Date | Lezen | ||||
| Disinfection 7 Last Slope Calibration Date | Lezen | ||||
| Disinfection 7 Last Zero Point Calibration Date | Lezen | ||||
| Disinfection 7 Slope | Lezen | ||||
| Disinfection 7 Slope Change Since Last Calibration | Lezen | ||||
| Disinfection 7 Zero Point | Lezen | ||||
| Disinfection 7 Zero Point Change Since Last Calibration | Lezen | ||||
| Disinfection 7 Temperature Offset | K | Lezen | |||
| Disinfection 7 Electrical Charge | Lezen | ||||
| Disinfection 7 Min Measured Value | Lezen | ||||
| Disinfection 7 Min Measured Temperature | °C | Lezen | |||
| Disinfection 7 Max Measured Value | Lezen | ||||
| Disinfection 7 Max Measured Temperature | °C | Lezen | |||
| Disinfection 7 Operating Hours | s | Lezen | |||
| Disinfection 7 Operating Time Above 15 C | s | Lezen | |||
| Disinfection 7 Operating Time Above 30 C | s | Lezen | |||
| Disinfection 7 Operating Time Below -20 nA | s | Lezen | |||
| Disinfection 7 Operating Time Below -100 nA | s | Lezen | |||
| Disinfection 7 Sensor Cap Calibrations | Lezen | ||||
| Disinfection 7 Diagnosis Code | Lezen | ||||
| Disinfection 7 NAMUR NE107 Status | Lezen | ||||
| Disinfection 7 Selected Sensor Type | Lezen | ||||
| Disinfection 7 Number Of Calibrations | Lezen | ||||
| Disinfection 7 Number Of Sterilizations | Lezen | ||||
| Disinfection 7 Clean In Place Cycles | Lezen | ||||
| Disinfection 7 Number Of Autoclavings | Lezen | ||||
| Disinfection 7 Cap Sterilization Cycles | Lezen | ||||
| Disinfection 7 Cap Clean In Place Cycles | Lezen | ||||
| Disinfection 7 Cap Autoclavings | Lezen | ||||
| Disinfection 7 Electrolyte Capacity | Lezen | ||||
| Disinfection 7 Operating Hours Above T3 | s | Lezen | |||
| Disinfection 7 Cap Operating Hours | s | Lezen | |||
| Disinfection 7 Cap Operating Hours Above T1 | s | Lezen | |||
| Disinfection 7 Cap Operating Hours Above T2 | s | Lezen | |||
| Disinfection 7 Cap Operating Hours Above T3 | s | Lezen | |||
| Disinfection 7 Cap Operating Hours Above T4 | s | Lezen | |||
| Disinfection 7 Cap Operating Hours Above T5 | s | Lezen | |||
| Disinfection 7 Sensor Element | Lezen | ||||
| Disinfection 7 Temperature Threshold T1 | Lezen | ||||
| Disinfection 7 Temperature Threshold T2 | Lezen | ||||
| Disinfection 7 Temperature Threshold T3 | Lezen | ||||
| Disinfection 7 Current Threshold T4 | A | Lezen | |||
| Disinfection 7 Current Threshold T5 | A | Lezen | |||
| Disinfection 8 Diagnosis Time | Lezen | ||||
| Disinfection 8 Manufacturing Date | Lezen | ||||
| Disinfection 8 Initial Operation Date | Lezen | ||||
| Disinfection 8 Last Slope Calibration Date | Lezen | ||||
| Disinfection 8 Last Zero Point Calibration Date | Lezen | ||||
| Disinfection 8 Slope | Lezen | ||||
| Disinfection 8 Slope Change Since Last Calibration | Lezen | ||||
| Disinfection 8 Zero Point | Lezen | ||||
| Disinfection 8 Zero Point Change Since Last Calibration | Lezen | ||||
| Disinfection 8 Temperature Offset | K | Lezen | |||
| Disinfection 8 Electrical Charge | Lezen | ||||
| Disinfection 8 Min Measured Value | Lezen | ||||
| Disinfection 8 Min Measured Temperature | °C | Lezen | |||
| Disinfection 8 Max Measured Value | Lezen | ||||
| Disinfection 8 Max Measured Temperature | °C | Lezen | |||
| Disinfection 8 Operating Hours | s | Lezen | |||
| Disinfection 8 Operating Time Above 15 C | s | Lezen | |||
| Disinfection 8 Operating Time Above 30 C | s | Lezen | |||
| Disinfection 8 Operating Time Below -20 nA | s | Lezen | |||
| Disinfection 8 Operating Time Below -100 nA | s | Lezen | |||
| Disinfection 8 Sensor Cap Calibrations | Lezen | ||||
| Disinfection 8 Diagnosis Code | Lezen | ||||
| Disinfection 8 NAMUR NE107 Status | Lezen | ||||
| Disinfection 8 Selected Sensor Type | Lezen | ||||
| Disinfection 8 Number Of Calibrations | Lezen | ||||
| Disinfection 8 Number Of Sterilizations | Lezen | ||||
| Disinfection 8 Clean In Place Cycles | Lezen | ||||
| Disinfection 8 Number Of Autoclavings | Lezen | ||||
| Disinfection 8 Cap Sterilization Cycles | Lezen | ||||
| Disinfection 8 Cap Clean In Place Cycles | Lezen | ||||
| Disinfection 8 Cap Autoclavings | Lezen | ||||
| Disinfection 8 Electrolyte Capacity | Lezen | ||||
| Disinfection 8 Operating Hours Above T3 | s | Lezen | |||
| Disinfection 8 Cap Operating Hours | s | Lezen | |||
| Disinfection 8 Cap Operating Hours Above T1 | s | Lezen | |||
| Disinfection 8 Cap Operating Hours Above T2 | s | Lezen | |||
| Disinfection 8 Cap Operating Hours Above T3 | s | Lezen | |||
| Disinfection 8 Cap Operating Hours Above T4 | s | Lezen | |||
| Disinfection 8 Cap Operating Hours Above T5 | s | Lezen | |||
| Disinfection 8 Sensor Element | Lezen | ||||
| Disinfection 8 Temperature Threshold T1 | Lezen | ||||
| Disinfection 8 Temperature Threshold T2 | Lezen | ||||
| Disinfection 8 Temperature Threshold T3 | Lezen | ||||
| Disinfection 8 Current Threshold T4 | A | Lezen | |||
| Disinfection 8 Current Threshold T5 | A | Lezen | |||
| Oxygen 1 Diagnosis Time | Lezen | ||||
| Oxygen 1 Manufacturing Date | Lezen | ||||
| Oxygen 1 Initial Operation Date | Lezen | ||||
| Oxygen 1 Last Calibration Date | Lezen | ||||
| Oxygen 1 Last Zero Point Calibration Date | Lezen | ||||
| Oxygen 1 Slope | Lezen | ||||
| Oxygen 1 Slope Change Since Last Calibration | Lezen | ||||
| Oxygen 1 Zero Point | Lezen | ||||
| Oxygen 1 Offset 26 Change Since Last Calibration | Lezen | ||||
| Oxygen 1 Temperature Offset | K | Lezen | |||
| Oxygen 1 Electrical Charge | Lezen | ||||
| Oxygen 1 Min Measured Temperature | °C | Lezen | |||
| Oxygen 1 Max Measured Temperature | °C | Lezen | |||
| Oxygen 1 Operating Hours | s | Lezen | |||
| Oxygen 1 Operating Time Below 5 C | s | Lezen | |||
| Oxygen 1 Operating Time Counter 40 | s | Lezen | |||
| Oxygen 1 Operating Time Counter 42 | s | Lezen | |||
| Oxygen 1 Operating Time Counter 44 | s | Lezen | |||
| Oxygen 1 Operating Time Counter 46 | s | Lezen | |||
| Oxygen 1 Operating Time Counter 48 | s | Lezen | |||
| Oxygen 1 Operating Time Counter 50 | s | Lezen | |||
| Oxygen 1 Operating Time Counter 52 | s | Lezen | |||
| Oxygen 1 Operating Time Below 25 us | s | Lezen | |||
| Oxygen 1 Operating Time Above 40 us | s | Lezen | |||
| Oxygen 1 Sterilization Cycles | Lezen | ||||
| Oxygen 1 Clean In Place Cycles | Lezen | ||||
| Oxygen 1 Number Of Calibrations | Lezen | ||||
| Oxygen 1 Sensor Cap Calibrations | Lezen | ||||
| Oxygen 1 Diagnosis Code | Lezen | ||||
| Oxygen 1 NAMUR NE107 Status | Lezen | ||||
| Oxygen 1 Selected Sensor Type | Lezen | ||||
| Oxygen 1 Ksv Point At Oxygen Calibration | Lezen | ||||
| Oxygen 1 Ksv Zero Point Calibration | Lezen | ||||
| Oxygen 1 Tau0 Point At Oxygen Calibration | Lezen | ||||
| Oxygen 1 Tau0 Zero Point Calibration | Lezen | ||||
| Oxygen 1 Quality Index Point At Oxygen Cal | Lezen | ||||
| Oxygen 1 Quality Index Zero Point Cal | Lezen | ||||
| Oxygen 1 Calibration Slope Absolute | Lezen | ||||
| Oxygen 1 Calibration Slope Change Absolute | Lezen | ||||
| Oxygen 1 Fermenter Scaling Factor | Lezen | ||||
| Oxygen 1 Temperature Threshold T1 | Lezen | ||||
| Oxygen 1 Temperature Threshold T2 | Lezen | ||||
| Oxygen 1 Temperature Threshold T3 | Lezen | ||||
| Oxygen 1 Temperature Threshold T4 | Lezen | ||||
| Oxygen 1 Cap Operating Hours | s | Lezen | |||
| Oxygen 1 Cap Operating Hours Above T1 | s | Lezen | |||
| Oxygen 1 Cap Operating Hours Above T2 | s | Lezen | |||
| Oxygen 1 Cap Operating Hours Above T3 | s | Lezen | |||
| Oxygen 1 Cap Operating Hours Below T4 | s | Lezen | |||
| Oxygen 1 Number Of Autoclavings | Lezen | ||||
| Oxygen 1 Cap Clean In Place Cycles | Lezen | ||||
| Oxygen 1 Cap Autoclavings | Lezen | ||||
| Oxygen 1 Cap Sterilization Cycles | Lezen | ||||
| Oxygen 1 Fermenter Scaling Active | Lezen | ||||
| Oxygen 1 Last Fermenter Scaling Date | Lezen | ||||
| Oxygen 1 Point At Oxygen Calibrations | Lezen | ||||
| Oxygen 1 Zero Point Calibrations | Lezen | ||||
| Oxygen 1 Mode Point At Oxygen Calibration | Lezen | ||||
| Oxygen 1 Mode Zero Point Calibration | Lezen | ||||
| Oxygen 2 Diagnosis Time | Lezen | ||||
| Oxygen 2 Manufacturing Date | Lezen | ||||
| Oxygen 2 Initial Operation Date | Lezen | ||||
| Oxygen 2 Last Calibration Date | Lezen | ||||
| Oxygen 2 Last Zero Point Calibration Date | Lezen | ||||
| Oxygen 2 Slope | Lezen | ||||
| Oxygen 2 Slope Change Since Last Calibration | Lezen | ||||
| Oxygen 2 Zero Point | Lezen | ||||
| Oxygen 2 Offset 26 Change Since Last Calibration | Lezen | ||||
| Oxygen 2 Temperature Offset | K | Lezen | |||
| Oxygen 2 Electrical Charge | Lezen | ||||
| Oxygen 2 Min Measured Temperature | °C | Lezen | |||
| Oxygen 2 Max Measured Temperature | °C | Lezen | |||
| Oxygen 2 Operating Hours | s | Lezen | |||
| Oxygen 2 Operating Time Below 5 C | s | Lezen | |||
| Oxygen 2 Operating Time Counter 40 | s | Lezen | |||
| Oxygen 2 Operating Time Counter 42 | s | Lezen | |||
| Oxygen 2 Operating Time Counter 44 | s | Lezen | |||
| Oxygen 2 Operating Time Counter 46 | s | Lezen | |||
| Oxygen 2 Operating Time Counter 48 | s | Lezen | |||
| Oxygen 2 Operating Time Counter 50 | s | Lezen | |||
| Oxygen 2 Operating Time Counter 52 | s | Lezen | |||
| Oxygen 2 Operating Time Below 25 us | s | Lezen | |||
| Oxygen 2 Operating Time Above 40 us | s | Lezen | |||
| Oxygen 2 Sterilization Cycles | Lezen | ||||
| Oxygen 2 Clean In Place Cycles | Lezen | ||||
| Oxygen 2 Number Of Calibrations | Lezen | ||||
| Oxygen 2 Sensor Cap Calibrations | Lezen | ||||
| Oxygen 2 Diagnosis Code | Lezen | ||||
| Oxygen 2 NAMUR NE107 Status | Lezen | ||||
| Oxygen 2 Selected Sensor Type | Lezen | ||||
| Oxygen 2 Ksv Point At Oxygen Calibration | Lezen | ||||
| Oxygen 2 Ksv Zero Point Calibration | Lezen | ||||
| Oxygen 2 Tau0 Point At Oxygen Calibration | Lezen | ||||
| Oxygen 2 Tau0 Zero Point Calibration | Lezen | ||||
| Oxygen 2 Quality Index Point At Oxygen Cal | Lezen | ||||
| Oxygen 2 Quality Index Zero Point Cal | Lezen | ||||
| Oxygen 2 Calibration Slope Absolute | Lezen | ||||
| Oxygen 2 Calibration Slope Change Absolute | Lezen | ||||
| Oxygen 2 Fermenter Scaling Factor | Lezen | ||||
| Oxygen 2 Temperature Threshold T1 | Lezen | ||||
| Oxygen 2 Temperature Threshold T2 | Lezen | ||||
| Oxygen 2 Temperature Threshold T3 | Lezen | ||||
| Oxygen 2 Temperature Threshold T4 | Lezen | ||||
| Oxygen 2 Cap Operating Hours | s | Lezen | |||
| Oxygen 2 Cap Operating Hours Above T1 | s | Lezen | |||
| Oxygen 2 Cap Operating Hours Above T2 | s | Lezen | |||
| Oxygen 2 Cap Operating Hours Above T3 | s | Lezen | |||
| Oxygen 2 Cap Operating Hours Below T4 | s | Lezen | |||
| Oxygen 2 Number Of Autoclavings | Lezen | ||||
| Oxygen 2 Cap Clean In Place Cycles | Lezen | ||||
| Oxygen 2 Cap Autoclavings | Lezen | ||||
| Oxygen 2 Cap Sterilization Cycles | Lezen | ||||
| Oxygen 2 Fermenter Scaling Active | Lezen | ||||
| Oxygen 2 Last Fermenter Scaling Date | Lezen | ||||
| Oxygen 2 Point At Oxygen Calibrations | Lezen | ||||
| Oxygen 2 Zero Point Calibrations | Lezen | ||||
| Oxygen 2 Mode Point At Oxygen Calibration | Lezen | ||||
| Oxygen 2 Mode Zero Point Calibration | Lezen | ||||
| Oxygen 3 Diagnosis Time | Lezen | ||||
| Oxygen 3 Manufacturing Date | Lezen | ||||
| Oxygen 3 Initial Operation Date | Lezen | ||||
| Oxygen 3 Last Calibration Date | Lezen | ||||
| Oxygen 3 Last Zero Point Calibration Date | Lezen | ||||
| Oxygen 3 Slope | Lezen | ||||
| Oxygen 3 Slope Change Since Last Calibration | Lezen | ||||
| Oxygen 3 Zero Point | Lezen | ||||
| Oxygen 3 Offset 26 Change Since Last Calibration | Lezen | ||||
| Oxygen 3 Temperature Offset | K | Lezen | |||
| Oxygen 3 Electrical Charge | Lezen | ||||
| Oxygen 3 Min Measured Temperature | °C | Lezen | |||
| Oxygen 3 Max Measured Temperature | °C | Lezen | |||
| Oxygen 3 Operating Hours | s | Lezen | |||
| Oxygen 3 Operating Time Below 5 C | s | Lezen | |||
| Oxygen 3 Operating Time Counter 40 | s | Lezen | |||
| Oxygen 3 Operating Time Counter 42 | s | Lezen | |||
| Oxygen 3 Operating Time Counter 44 | s | Lezen | |||
| Oxygen 3 Operating Time Counter 46 | s | Lezen | |||
| Oxygen 3 Operating Time Counter 48 | s | Lezen | |||
| Oxygen 3 Operating Time Counter 50 | s | Lezen | |||
| Oxygen 3 Operating Time Counter 52 | s | Lezen | |||
| Oxygen 3 Operating Time Below 25 us | s | Lezen | |||
| Oxygen 3 Operating Time Above 40 us | s | Lezen | |||
| Oxygen 3 Sterilization Cycles | Lezen | ||||
| Oxygen 3 Clean In Place Cycles | Lezen | ||||
| Oxygen 3 Number Of Calibrations | Lezen | ||||
| Oxygen 3 Sensor Cap Calibrations | Lezen | ||||
| Oxygen 3 Diagnosis Code | Lezen | ||||
| Oxygen 3 NAMUR NE107 Status | Lezen | ||||
| Oxygen 3 Selected Sensor Type | Lezen | ||||
| Oxygen 3 Ksv Point At Oxygen Calibration | Lezen | ||||
| Oxygen 3 Ksv Zero Point Calibration | Lezen | ||||
| Oxygen 3 Tau0 Point At Oxygen Calibration | Lezen | ||||
| Oxygen 3 Tau0 Zero Point Calibration | Lezen | ||||
| Oxygen 3 Quality Index Point At Oxygen Cal | Lezen | ||||
| Oxygen 3 Quality Index Zero Point Cal | Lezen | ||||
| Oxygen 3 Calibration Slope Absolute | Lezen | ||||
| Oxygen 3 Calibration Slope Change Absolute | Lezen | ||||
| Oxygen 3 Fermenter Scaling Factor | Lezen | ||||
| Oxygen 3 Temperature Threshold T1 | Lezen | ||||
| Oxygen 3 Temperature Threshold T2 | Lezen | ||||
| Oxygen 3 Temperature Threshold T3 | Lezen | ||||
| Oxygen 3 Temperature Threshold T4 | Lezen | ||||
| Oxygen 3 Cap Operating Hours | s | Lezen | |||
| Oxygen 3 Cap Operating Hours Above T1 | s | Lezen | |||
| Oxygen 3 Cap Operating Hours Above T2 | s | Lezen | |||
| Oxygen 3 Cap Operating Hours Above T3 | s | Lezen | |||
| Oxygen 3 Cap Operating Hours Below T4 | s | Lezen | |||
| Oxygen 3 Number Of Autoclavings | Lezen | ||||
| Oxygen 3 Cap Clean In Place Cycles | Lezen | ||||
| Oxygen 3 Cap Autoclavings | Lezen | ||||
| Oxygen 3 Cap Sterilization Cycles | Lezen | ||||
| Oxygen 3 Fermenter Scaling Active | Lezen | ||||
| Oxygen 3 Last Fermenter Scaling Date | Lezen | ||||
| Oxygen 3 Point At Oxygen Calibrations | Lezen | ||||
| Oxygen 3 Zero Point Calibrations | Lezen | ||||
| Oxygen 3 Mode Point At Oxygen Calibration | Lezen | ||||
| Oxygen 3 Mode Zero Point Calibration | Lezen | ||||
| Oxygen 4 Diagnosis Time | Lezen | ||||
| Oxygen 4 Manufacturing Date | Lezen | ||||
| Oxygen 4 Initial Operation Date | Lezen | ||||
| Oxygen 4 Last Calibration Date | Lezen | ||||
| Oxygen 4 Last Zero Point Calibration Date | Lezen | ||||
| Oxygen 4 Slope | Lezen | ||||
| Oxygen 4 Slope Change Since Last Calibration | Lezen | ||||
| Oxygen 4 Zero Point | Lezen | ||||
| Oxygen 4 Offset 26 Change Since Last Calibration | Lezen | ||||
| Oxygen 4 Temperature Offset | K | Lezen | |||
| Oxygen 4 Electrical Charge | Lezen | ||||
| Oxygen 4 Min Measured Temperature | °C | Lezen | |||
| Oxygen 4 Max Measured Temperature | °C | Lezen | |||
| Oxygen 4 Operating Hours | s | Lezen | |||
| Oxygen 4 Operating Time Below 5 C | s | Lezen | |||
| Oxygen 4 Operating Time Counter 40 | s | Lezen | |||
| Oxygen 4 Operating Time Counter 42 | s | Lezen | |||
| Oxygen 4 Operating Time Counter 44 | s | Lezen | |||
| Oxygen 4 Operating Time Counter 46 | s | Lezen | |||
| Oxygen 4 Operating Time Counter 48 | s | Lezen | |||
| Oxygen 4 Operating Time Counter 50 | s | Lezen | |||
| Oxygen 4 Operating Time Counter 52 | s | Lezen | |||
| Oxygen 4 Operating Time Below 25 us | s | Lezen | |||
| Oxygen 4 Operating Time Above 40 us | s | Lezen | |||
| Oxygen 4 Sterilization Cycles | Lezen | ||||
| Oxygen 4 Clean In Place Cycles | Lezen | ||||
| Oxygen 4 Number Of Calibrations | Lezen | ||||
| Oxygen 4 Sensor Cap Calibrations | Lezen | ||||
| Oxygen 4 Diagnosis Code | Lezen | ||||
| Oxygen 4 NAMUR NE107 Status | Lezen | ||||
| Oxygen 4 Selected Sensor Type | Lezen | ||||
| Oxygen 4 Ksv Point At Oxygen Calibration | Lezen | ||||
| Oxygen 4 Ksv Zero Point Calibration | Lezen | ||||
| Oxygen 4 Tau0 Point At Oxygen Calibration | Lezen | ||||
| Oxygen 4 Tau0 Zero Point Calibration | Lezen | ||||
| Oxygen 4 Quality Index Point At Oxygen Cal | Lezen | ||||
| Oxygen 4 Quality Index Zero Point Cal | Lezen | ||||
| Oxygen 4 Calibration Slope Absolute | Lezen | ||||
| Oxygen 4 Calibration Slope Change Absolute | Lezen | ||||
| Oxygen 4 Fermenter Scaling Factor | Lezen | ||||
| Oxygen 4 Temperature Threshold T1 | Lezen | ||||
| Oxygen 4 Temperature Threshold T2 | Lezen | ||||
| Oxygen 4 Temperature Threshold T3 | Lezen | ||||
| Oxygen 4 Temperature Threshold T4 | Lezen | ||||
| Oxygen 4 Cap Operating Hours | s | Lezen | |||
| Oxygen 4 Cap Operating Hours Above T1 | s | Lezen | |||
| Oxygen 4 Cap Operating Hours Above T2 | s | Lezen | |||
| Oxygen 4 Cap Operating Hours Above T3 | s | Lezen | |||
| Oxygen 4 Cap Operating Hours Below T4 | s | Lezen | |||
| Oxygen 4 Number Of Autoclavings | Lezen | ||||
| Oxygen 4 Cap Clean In Place Cycles | Lezen | ||||
| Oxygen 4 Cap Autoclavings | Lezen | ||||
| Oxygen 4 Cap Sterilization Cycles | Lezen | ||||
| Oxygen 4 Fermenter Scaling Active | Lezen | ||||
| Oxygen 4 Last Fermenter Scaling Date | Lezen | ||||
| Oxygen 4 Point At Oxygen Calibrations | Lezen | ||||
| Oxygen 4 Zero Point Calibrations | Lezen | ||||
| Oxygen 4 Mode Point At Oxygen Calibration | Lezen | ||||
| Oxygen 4 Mode Zero Point Calibration | Lezen | ||||
| Oxygen 5 Diagnosis Time | Lezen | ||||
| Oxygen 5 Manufacturing Date | Lezen | ||||
| Oxygen 5 Initial Operation Date | Lezen | ||||
| Oxygen 5 Last Calibration Date | Lezen | ||||
| Oxygen 5 Last Zero Point Calibration Date | Lezen | ||||
| Oxygen 5 Slope | Lezen | ||||
| Oxygen 5 Slope Change Since Last Calibration | Lezen | ||||
| Oxygen 5 Zero Point | Lezen | ||||
| Oxygen 5 Offset 26 Change Since Last Calibration | Lezen | ||||
| Oxygen 5 Temperature Offset | K | Lezen | |||
| Oxygen 5 Electrical Charge | Lezen | ||||
| Oxygen 5 Min Measured Temperature | °C | Lezen | |||
| Oxygen 5 Max Measured Temperature | °C | Lezen | |||
| Oxygen 5 Operating Hours | s | Lezen | |||
| Oxygen 5 Operating Time Below 5 C | s | Lezen | |||
| Oxygen 5 Operating Time Counter 40 | s | Lezen | |||
| Oxygen 5 Operating Time Counter 42 | s | Lezen | |||
| Oxygen 5 Operating Time Counter 44 | s | Lezen | |||
| Oxygen 5 Operating Time Counter 46 | s | Lezen | |||
| Oxygen 5 Operating Time Counter 48 | s | Lezen | |||
| Oxygen 5 Operating Time Counter 50 | s | Lezen | |||
| Oxygen 5 Operating Time Counter 52 | s | Lezen | |||
| Oxygen 5 Operating Time Below 25 us | s | Lezen | |||
| Oxygen 5 Operating Time Above 40 us | s | Lezen | |||
| Oxygen 5 Sterilization Cycles | Lezen | ||||
| Oxygen 5 Clean In Place Cycles | Lezen | ||||
| Oxygen 5 Number Of Calibrations | Lezen | ||||
| Oxygen 5 Sensor Cap Calibrations | Lezen | ||||
| Oxygen 5 Diagnosis Code | Lezen | ||||
| Oxygen 5 NAMUR NE107 Status | Lezen | ||||
| Oxygen 5 Selected Sensor Type | Lezen | ||||
| Oxygen 5 Ksv Point At Oxygen Calibration | Lezen | ||||
| Oxygen 5 Ksv Zero Point Calibration | Lezen | ||||
| Oxygen 5 Tau0 Point At Oxygen Calibration | Lezen | ||||
| Oxygen 5 Tau0 Zero Point Calibration | Lezen | ||||
| Oxygen 5 Quality Index Point At Oxygen Cal | Lezen | ||||
| Oxygen 5 Quality Index Zero Point Cal | Lezen | ||||
| Oxygen 5 Calibration Slope Absolute | Lezen | ||||
| Oxygen 5 Calibration Slope Change Absolute | Lezen | ||||
| Oxygen 5 Fermenter Scaling Factor | Lezen | ||||
| Oxygen 5 Temperature Threshold T1 | Lezen | ||||
| Oxygen 5 Temperature Threshold T2 | Lezen | ||||
| Oxygen 5 Temperature Threshold T3 | Lezen | ||||
| Oxygen 5 Temperature Threshold T4 | Lezen | ||||
| Oxygen 5 Cap Operating Hours | s | Lezen | |||
| Oxygen 5 Cap Operating Hours Above T1 | s | Lezen | |||
| Oxygen 5 Cap Operating Hours Above T2 | s | Lezen | |||
| Oxygen 5 Cap Operating Hours Above T3 | s | Lezen | |||
| Oxygen 5 Cap Operating Hours Below T4 | s | Lezen | |||
| Oxygen 5 Number Of Autoclavings | Lezen | ||||
| Oxygen 5 Cap Clean In Place Cycles | Lezen | ||||
| Oxygen 5 Cap Autoclavings | Lezen | ||||
| Oxygen 5 Cap Sterilization Cycles | Lezen | ||||
| Oxygen 5 Fermenter Scaling Active | Lezen | ||||
| Oxygen 5 Last Fermenter Scaling Date | Lezen | ||||
| Oxygen 5 Point At Oxygen Calibrations | Lezen | ||||
| Oxygen 5 Zero Point Calibrations | Lezen | ||||
| Oxygen 5 Mode Point At Oxygen Calibration | Lezen | ||||
| Oxygen 5 Mode Zero Point Calibration | Lezen | ||||
| Oxygen 6 Diagnosis Time | Lezen | ||||
| Oxygen 6 Manufacturing Date | Lezen | ||||
| Oxygen 6 Initial Operation Date | Lezen | ||||
| Oxygen 6 Last Calibration Date | Lezen | ||||
| Oxygen 6 Last Zero Point Calibration Date | Lezen | ||||
| Oxygen 6 Slope | Lezen | ||||
| Oxygen 6 Slope Change Since Last Calibration | Lezen | ||||
| Oxygen 6 Zero Point | Lezen | ||||
| Oxygen 6 Offset 26 Change Since Last Calibration | Lezen | ||||
| Oxygen 6 Temperature Offset | K | Lezen | |||
| Oxygen 6 Electrical Charge | Lezen | ||||
| Oxygen 6 Min Measured Temperature | °C | Lezen | |||
| Oxygen 6 Max Measured Temperature | °C | Lezen | |||
| Oxygen 6 Operating Hours | s | Lezen | |||
| Oxygen 6 Operating Time Below 5 C | s | Lezen | |||
| Oxygen 6 Operating Time Counter 40 | s | Lezen | |||
| Oxygen 6 Operating Time Counter 42 | s | Lezen | |||
| Oxygen 6 Operating Time Counter 44 | s | Lezen | |||
| Oxygen 6 Operating Time Counter 46 | s | Lezen | |||
| Oxygen 6 Operating Time Counter 48 | s | Lezen | |||
| Oxygen 6 Operating Time Counter 50 | s | Lezen | |||
| Oxygen 6 Operating Time Counter 52 | s | Lezen | |||
| Oxygen 6 Operating Time Below 25 us | s | Lezen | |||
| Oxygen 6 Operating Time Above 40 us | s | Lezen | |||
| Oxygen 6 Sterilization Cycles | Lezen | ||||
| Oxygen 6 Clean In Place Cycles | Lezen | ||||
| Oxygen 6 Number Of Calibrations | Lezen | ||||
| Oxygen 6 Sensor Cap Calibrations | Lezen | ||||
| Oxygen 6 Diagnosis Code | Lezen | ||||
| Oxygen 6 NAMUR NE107 Status | Lezen | ||||
| Oxygen 6 Selected Sensor Type | Lezen | ||||
| Oxygen 6 Ksv Point At Oxygen Calibration | Lezen | ||||
| Oxygen 6 Ksv Zero Point Calibration | Lezen | ||||
| Oxygen 6 Tau0 Point At Oxygen Calibration | Lezen | ||||
| Oxygen 6 Tau0 Zero Point Calibration | Lezen | ||||
| Oxygen 6 Quality Index Point At Oxygen Cal | Lezen | ||||
| Oxygen 6 Quality Index Zero Point Cal | Lezen | ||||
| Oxygen 6 Calibration Slope Absolute | Lezen | ||||
| Oxygen 6 Calibration Slope Change Absolute | Lezen | ||||
| Oxygen 6 Fermenter Scaling Factor | Lezen | ||||
| Oxygen 6 Temperature Threshold T1 | Lezen | ||||
| Oxygen 6 Temperature Threshold T2 | Lezen | ||||
| Oxygen 6 Temperature Threshold T3 | Lezen | ||||
| Oxygen 6 Temperature Threshold T4 | Lezen | ||||
| Oxygen 6 Cap Operating Hours | s | Lezen | |||
| Oxygen 6 Cap Operating Hours Above T1 | s | Lezen | |||
| Oxygen 6 Cap Operating Hours Above T2 | s | Lezen | |||
| Oxygen 6 Cap Operating Hours Above T3 | s | Lezen | |||
| Oxygen 6 Cap Operating Hours Below T4 | s | Lezen | |||
| Oxygen 6 Number Of Autoclavings | Lezen | ||||
| Oxygen 6 Cap Clean In Place Cycles | Lezen | ||||
| Oxygen 6 Cap Autoclavings | Lezen | ||||
| Oxygen 6 Cap Sterilization Cycles | Lezen | ||||
| Oxygen 6 Fermenter Scaling Active | Lezen | ||||
| Oxygen 6 Last Fermenter Scaling Date | Lezen | ||||
| Oxygen 6 Point At Oxygen Calibrations | Lezen | ||||
| Oxygen 6 Zero Point Calibrations | Lezen | ||||
| Oxygen 6 Mode Point At Oxygen Calibration | Lezen | ||||
| Oxygen 6 Mode Zero Point Calibration | Lezen | ||||
| Oxygen 7 Diagnosis Time | Lezen | ||||
| Oxygen 7 Manufacturing Date | Lezen | ||||
| Oxygen 7 Initial Operation Date | Lezen | ||||
| Oxygen 7 Last Calibration Date | Lezen | ||||
| Oxygen 7 Last Zero Point Calibration Date | Lezen | ||||
| Oxygen 7 Slope | Lezen | ||||
| Oxygen 7 Slope Change Since Last Calibration | Lezen | ||||
| Oxygen 7 Zero Point | Lezen | ||||
| Oxygen 7 Offset 26 Change Since Last Calibration | Lezen | ||||
| Oxygen 7 Temperature Offset | K | Lezen | |||
| Oxygen 7 Electrical Charge | Lezen | ||||
| Oxygen 7 Min Measured Temperature | °C | Lezen | |||
| Oxygen 7 Max Measured Temperature | °C | Lezen | |||
| Oxygen 7 Operating Hours | s | Lezen | |||
| Oxygen 7 Operating Time Below 5 C | s | Lezen | |||
| Oxygen 7 Operating Time Counter 40 | s | Lezen | |||
| Oxygen 7 Operating Time Counter 42 | s | Lezen | |||
| Oxygen 7 Operating Time Counter 44 | s | Lezen | |||
| Oxygen 7 Operating Time Counter 46 | s | Lezen | |||
| Oxygen 7 Operating Time Counter 48 | s | Lezen | |||
| Oxygen 7 Operating Time Counter 50 | s | Lezen | |||
| Oxygen 7 Operating Time Counter 52 | s | Lezen | |||
| Oxygen 7 Operating Time Below 25 us | s | Lezen | |||
| Oxygen 7 Operating Time Above 40 us | s | Lezen | |||
| Oxygen 7 Sterilization Cycles | Lezen | ||||
| Oxygen 7 Clean In Place Cycles | Lezen | ||||
| Oxygen 7 Number Of Calibrations | Lezen | ||||
| Oxygen 7 Sensor Cap Calibrations | Lezen | ||||
| Oxygen 7 Diagnosis Code | Lezen | ||||
| Oxygen 7 NAMUR NE107 Status | Lezen | ||||
| Oxygen 7 Selected Sensor Type | Lezen | ||||
| Oxygen 7 Ksv Point At Oxygen Calibration | Lezen | ||||
| Oxygen 7 Ksv Zero Point Calibration | Lezen | ||||
| Oxygen 7 Tau0 Point At Oxygen Calibration | Lezen | ||||
| Oxygen 7 Tau0 Zero Point Calibration | Lezen | ||||
| Oxygen 7 Quality Index Point At Oxygen Cal | Lezen | ||||
| Oxygen 7 Quality Index Zero Point Cal | Lezen | ||||
| Oxygen 7 Calibration Slope Absolute | Lezen | ||||
| Oxygen 7 Calibration Slope Change Absolute | Lezen | ||||
| Oxygen 7 Fermenter Scaling Factor | Lezen | ||||
| Oxygen 7 Temperature Threshold T1 | Lezen | ||||
| Oxygen 7 Temperature Threshold T2 | Lezen | ||||
| Oxygen 7 Temperature Threshold T3 | Lezen | ||||
| Oxygen 7 Temperature Threshold T4 | Lezen | ||||
| Oxygen 7 Cap Operating Hours | s | Lezen | |||
| Oxygen 7 Cap Operating Hours Above T1 | s | Lezen | |||
| Oxygen 7 Cap Operating Hours Above T2 | s | Lezen | |||
| Oxygen 7 Cap Operating Hours Above T3 | s | Lezen | |||
| Oxygen 7 Cap Operating Hours Below T4 | s | Lezen | |||
| Oxygen 7 Number Of Autoclavings | Lezen | ||||
| Oxygen 7 Cap Clean In Place Cycles | Lezen | ||||
| Oxygen 7 Cap Autoclavings | Lezen | ||||
| Oxygen 7 Cap Sterilization Cycles | Lezen | ||||
| Oxygen 7 Fermenter Scaling Active | Lezen | ||||
| Oxygen 7 Last Fermenter Scaling Date | Lezen | ||||
| Oxygen 7 Point At Oxygen Calibrations | Lezen | ||||
| Oxygen 7 Zero Point Calibrations | Lezen | ||||
| Oxygen 7 Mode Point At Oxygen Calibration | Lezen | ||||
| Oxygen 7 Mode Zero Point Calibration | Lezen | ||||
| Oxygen 8 Diagnosis Time | Lezen | ||||
| Oxygen 8 Manufacturing Date | Lezen | ||||
| Oxygen 8 Initial Operation Date | Lezen | ||||
| Oxygen 8 Last Calibration Date | Lezen | ||||
| Oxygen 8 Last Zero Point Calibration Date | Lezen | ||||
| Oxygen 8 Slope | Lezen | ||||
| Oxygen 8 Slope Change Since Last Calibration | Lezen | ||||
| Oxygen 8 Zero Point | Lezen | ||||
| Oxygen 8 Offset 26 Change Since Last Calibration | Lezen | ||||
| Oxygen 8 Temperature Offset | K | Lezen | |||
| Oxygen 8 Electrical Charge | Lezen | ||||
| Oxygen 8 Min Measured Temperature | °C | Lezen | |||
| Oxygen 8 Max Measured Temperature | °C | Lezen | |||
| Oxygen 8 Operating Hours | s | Lezen | |||
| Oxygen 8 Operating Time Below 5 C | s | Lezen | |||
| Oxygen 8 Operating Time Counter 40 | s | Lezen | |||
| Oxygen 8 Operating Time Counter 42 | s | Lezen | |||
| Oxygen 8 Operating Time Counter 44 | s | Lezen | |||
| Oxygen 8 Operating Time Counter 46 | s | Lezen | |||
| Oxygen 8 Operating Time Counter 48 | s | Lezen | |||
| Oxygen 8 Operating Time Counter 50 | s | Lezen | |||
| Oxygen 8 Operating Time Counter 52 | s | Lezen | |||
| Oxygen 8 Operating Time Below 25 us | s | Lezen | |||
| Oxygen 8 Operating Time Above 40 us | s | Lezen | |||
| Oxygen 8 Sterilization Cycles | Lezen | ||||
| Oxygen 8 Clean In Place Cycles | Lezen | ||||
| Oxygen 8 Number Of Calibrations | Lezen | ||||
| Oxygen 8 Sensor Cap Calibrations | Lezen | ||||
| Oxygen 8 Diagnosis Code | Lezen | ||||
| Oxygen 8 NAMUR NE107 Status | Lezen | ||||
| Oxygen 8 Selected Sensor Type | Lezen | ||||
| Oxygen 8 Ksv Point At Oxygen Calibration | Lezen | ||||
| Oxygen 8 Ksv Zero Point Calibration | Lezen | ||||
| Oxygen 8 Tau0 Point At Oxygen Calibration | Lezen | ||||
| Oxygen 8 Tau0 Zero Point Calibration | Lezen | ||||
| Oxygen 8 Quality Index Point At Oxygen Cal | Lezen | ||||
| Oxygen 8 Quality Index Zero Point Cal | Lezen | ||||
| Oxygen 8 Calibration Slope Absolute | Lezen | ||||
| Oxygen 8 Calibration Slope Change Absolute | Lezen | ||||
| Oxygen 8 Fermenter Scaling Factor | Lezen | ||||
| Oxygen 8 Temperature Threshold T1 | Lezen | ||||
| Oxygen 8 Temperature Threshold T2 | Lezen | ||||
| Oxygen 8 Temperature Threshold T3 | Lezen | ||||
| Oxygen 8 Temperature Threshold T4 | Lezen | ||||
| Oxygen 8 Cap Operating Hours | s | Lezen | |||
| Oxygen 8 Cap Operating Hours Above T1 | s | Lezen | |||
| Oxygen 8 Cap Operating Hours Above T2 | s | Lezen | |||
| Oxygen 8 Cap Operating Hours Above T3 | s | Lezen | |||
| Oxygen 8 Cap Operating Hours Below T4 | s | Lezen | |||
| Oxygen 8 Number Of Autoclavings | Lezen | ||||
| Oxygen 8 Cap Clean In Place Cycles | Lezen | ||||
| Oxygen 8 Cap Autoclavings | Lezen | ||||
| Oxygen 8 Cap Sterilization Cycles | Lezen | ||||
| Oxygen 8 Fermenter Scaling Active | Lezen | ||||
| Oxygen 8 Last Fermenter Scaling Date | Lezen | ||||
| Oxygen 8 Point At Oxygen Calibrations | Lezen | ||||
| Oxygen 8 Zero Point Calibrations | Lezen | ||||
| Oxygen 8 Mode Point At Oxygen Calibration | Lezen | ||||
| Oxygen 8 Mode Zero Point Calibration | Lezen |
Registers laden…
Stuur jouw apparatenlijst
Staat een apparaat niet in de bibliotheek, dan maken we de template gratis zodra we de registers hebben.
Gebruikstoepassingen
- Toon de NAMUR-status en diagnosecode van elke zuurstof- en chloorsensor op één dashboard.
- Krijg een alarm per e-mail als een sensor onderhoud nodig heeft of uitvalt.
- Volg helling en nulpunt na elke kalibratie in de historie om drift van een sensor te zien.
- Plan de vervanging van caps en membranen aan de hand van de bedrijfsuren van de cap en het aantal kalibraties.
- Zie wanneer elke sensor voor het laatst is gekalibreerd zonder naar de transmitter te lopen.
Installatie
Sluit de RS485-module van de Liquiline CM44x aan op de RS485-poort van de ModbusCloud Gateway, A op A en B op B, met afsluiting aan beide uiteinden van de bus.
Stel in het Modbus-menu van de transmitter het busadres, 19200 baud en even pariteit in, of zet het adres met de schakelaar op de module.
Voer de activeringscode voor Heartbeat Monitoring in op de transmitter als die nog niet actief is.
Voeg in ModbusCloud een Modbus apparaat toe met hetzelfde adres en dezelfde seriële instellingen, importeer deze template en verwijder de kanalen die je niet gebruikt.
Veelvoorkomende aandachtspunten
Alle Heartbeat-waarden staan op 0. Hoe kan dat?
Heartbeat Monitoring heeft een activeringscode nodig. Zonder die code antwoordt de transmitter wel, maar staat elk Heartbeat-register op 0. Controleer ook of op dat kanaal een sensor van het juiste type zit; een leeg kanaal geeft ook 0.
De datums zijn heel grote getallen. Hoe lees ik die?
De datums zijn DATETIME-waarden van 8 bytes, hier getoond als 64-bit getal. ModbusCloud laat de ruwe waarde zien; gebruik die om te zien wanneer een datum verandert, bijvoorbeeld na een kalibratie, niet als kalenderdatum.
De kommagetallen kloppen niet. Wat controleer ik?
De template gaat uit van de standaard bytevolgorde 1-0-3-2 van de transmitter. Heeft iemand de parameter Byte order in het Modbus-menu veranderd, dan komen de kommagetallen door elkaar. Zet hem terug op 1-0-3-2.
De transmitter antwoordt helemaal niet. Wat controleer ik?
Kijk of adres, baudrate en pariteit aan beide kanten gelijk zijn; standaard is adres 247, 19200 baud en even pariteit. Staat de adresschakelaar op de RS485-module ingesteld, dan gaat die voor het menu. Wissel zo nodig A en B en controleer de afsluiting.
Zelf zien hoe het werkt?
