WEG CFW11
Frequency inverter for three-phase motors: speed, current, power, faults and every drive parameter.
The WEG CFW11 is a frequency inverter that controls the speed and torque of three-phase induction and permanent magnet motors in pumps, fans, compressors and machines. This Modbus RTU template reads speed, current, power, temperatures and faults, and lets you write the control word, speed reference, ramps and drive parameters from ModbusCloud.
- Protocol
- Modbus RTU
- Connection
- RS485, 9600 baud
- Registers
- 602, read and write
- Brand
- WEG
- Key readings
- Motor speed · Motor current · Output power · Motor torque · DC link voltage · Heatsink temperature · Present fault and alarm · Drive status
- Available commands
- Run, stop and direction · Speed reference · Acceleration and deceleration time · Minimum and maximum speed · PID setpoint · Digital and analog outputs
- Compatible models
- CFW-11 · CFW-11M
- Last updated
Registers (602)
602 read, 431 write
| Name | Unit | Access | Address (Hidden until you enter your email) | Function (hidden) | Type (hidden) |
|---|---|---|---|---|---|
| Motor Speed | rpm | Read | 2 | FC03 | uint16 |
| Motor Current | A | Read | 3 | FC03 | uint16 |
| Motor Frequency | Hz | Read | 5 | FC03 | uint16 |
| DC Link Voltage (Ud) | V | Read | 4 | FC03 | uint16 |
| Motor Voltage | V | Read | 7 | FC03 | uint16 |
| Motor Torque | % | Read | |||
| Output Power | kW | Read | |||
| Output Cos phi | Read | ||||
| Speed Reference | rpm | Read | |||
| VFD Status | Read | ||||
| Present Alarm | Read | ||||
| Present Fault | Read | ||||
| IGBTs Temperature U | °C | Read | |||
| IGBTs Temperature V | °C | Read | |||
| IGBTs Temperature W | °C | Read | |||
| Rectifier Temperature | °C | Read | |||
| Internal Air Temp. | °C | Read | |||
| Control Air Temperature | °C | Read | |||
| Fan Heatsink Speed | rpm | Read | |||
| Motor Overload Status | % | Read | |||
| Time Powered | h | Read | |||
| Time Enabled | h | Read | |||
| kWh Output Energy | kWh | Read | |||
| Fan Enabled Time | h | Read | |||
| Logical Status | Read | ||||
| Speed in 13 bits | Read | ||||
| Serial/USB Control | Read and write | ||||
| Serial/USB Speed Ref. | Read and write | ||||
| Access to Parameters | Read and write | ||||
| DI8 to DI1 Status | Read | ||||
| DO5 to DO1 Status | Read | ||||
| AO1 Value | % | Read | |||
| AO2 Value | % | Read | |||
| AO3 Value | % | Read | |||
| AO4 Value | % | Read | |||
| AI1 Value | % | Read | |||
| AI2 Value | % | Read | |||
| AI3 Value | % | Read | |||
| AI4 Value | % | Read | |||
| Software Version | Read | ||||
| DI16 to DI9 Status | Read | ||||
| DO13 to DO6 Status | Read | ||||
| Accessories Config. 1 | Read | ||||
| Accessories Config. 2 | Read | ||||
| Power Hardware Config | Read | ||||
| Encoder Speed | rpm | Read | |||
| Encoder Pulses Count | Read | ||||
| PID Process Variable | % | Read | |||
| PID Setpoint Value | % | Read | |||
| Last Fault | Read | ||||
| Last Fault Day/Month | Read | ||||
| Last Fault Year | Read | ||||
| Last Fault Time | Read | ||||
| Second Fault | Read | ||||
| Second Flt. Day/Month | Read | ||||
| Second Fault Year | Read | ||||
| Second Fault Time | Read | ||||
| Third Fault | Read | ||||
| Third Fault Day/Month | Read | ||||
| Third Fault Year | Read | ||||
| Third Fault Time | Read | ||||
| Fourth Fault | Read | ||||
| Fourth Flt. Day/Month | Read | ||||
| Fourth Fault Year | Read | ||||
| Fourth Fault Time | Read | ||||
| Fifth Fault | Read | ||||
| Fifth Fault Day/Month | Read | ||||
| Fifth Fault Year | Read | ||||
| Fifth Fault Time | Read | ||||
| Sixth Fault | Read | ||||
| Sixth Fault Day/Month | Read | ||||
| Sixth Fault Year | Read | ||||
| Sixth Fault Time | Read | ||||
| Seventh Fault | Read | ||||
| Seventh Flt.Day/Month | Read | ||||
| Seventh Fault Year | Read | ||||
| Seventh Fault Time | Read | ||||
| Eighth Fault | Read | ||||
| Eighth Flt. Day/Month | Read | ||||
| Eighth Fault Year | Read | ||||
| Eighth Fault Time | Read | ||||
| Ninth Fault | Read | ||||
| Ninth Fault Day/Month | Read | ||||
| Ninth Fault Year | Read | ||||
| Ninth Fault Time | Read | ||||
| Tenth Fault | Read | ||||
| Tenth Fault Day/Month | Read | ||||
| Tenth Fault Year | Read | ||||
| Tenth Fault Time | Read | ||||
| Current At Last Fault | A | Read | |||
| DC Link At Last Fault | V | Read | |||
| Speed At Last Fault | rpm | Read | |||
| Reference Last Fault | rpm | Read | |||
| Frequency Last Fault | Hz | Read | |||
| Motor Volt.Last Fault | V | Read | |||
| DIx Status Last Fault | Read | ||||
| DOx Status Last Fault | Read | ||||
| Acceleration Time | s | Read and write | |||
| Deceleration Time | s | Read and write | |||
| Acceleration Time 2 | s | Read and write | |||
| Deceleration Time 2 | s | Read and write | |||
| S Ramp | Read and write | ||||
| 1st/2nd Ramp Select. | Read and write | ||||
| Speed Ref. Backup | Read and write | ||||
| Keypad Reference | rpm | Read and write | |||
| JOG/JOG+ Reference | rpm | Read and write | |||
| JOG- Reference | rpm | Read and write | |||
| Multispeed Ref. 1 | rpm | Read and write | |||
| Multispeed Ref. 2 | rpm | Read and write | |||
| Multispeed Ref. 3 | rpm | Read and write | |||
| Multispeed Ref. 4 | rpm | Read and write | |||
| Multispeed Ref. 5 | rpm | Read and write | |||
| Multispeed Ref. 6 | rpm | Read and write | |||
| Multispeed Ref. 7 | rpm | Read and write | |||
| Multispeed Ref. 8 | rpm | Read and write | |||
| Max. Overspeed Level | % | Read and write | |||
| Minimum Speed | rpm | Read and write | |||
| Maximum Speed | rpm | Read and write | |||
| Max. Output Current | A | Read and write | |||
| Manual Torque Boost | Read and write | ||||
| Autom. Torque Boost | Read and write | ||||
| Slip Compensation P0138 | % | Read and write | |||
| Output Current Filter | s | Read and write | |||
| Dwell Time At Start | s | Read and write | |||
| Dwell Speed At Start | rpm | Read and write | |||
| Max. Output Voltage P0142 | % | Read and write | |||
| Interm.Output Voltage | % | Read and write | |||
| 3Hz Output Voltage | % | Read and write | |||
| Field Weakening Speed | rpm | Read and write | |||
| Intermediate Speed | rpm | Read and write | |||
| DC Regul. Type V/f | Read and write | ||||
| DC Regul. Level V/f | V | Read and write | |||
| DC Link Regul. P Gain | Read and write | ||||
| Dyn. Braking Level | V | Read and write | |||
| Dyn. Braking Resistor | Ω | Read and write | |||
| Dyn. B. Resist. Power | kW | Read and write | |||
| Overl.Curr.100% Speed | A | Read and write | |||
| Overl.Curr. 50% Speed | A | Read and write | |||
| Overl.Curr. 5% Speed | A | Read and write | |||
| Motor Thermal Class | Read and write | ||||
| Speed Regul. Configuration | Read and write | ||||
| Speed Prop. Gain | Read and write | ||||
| Speed Integral Gain | Read and write | ||||
| LOC Reference Offset | Read and write | ||||
| REM Reference Offset | Read and write | ||||
| Speed Filter | s | Read and write | |||
| Speed Diff. Gain | Read and write | ||||
| Current Prop. Gain | Read and write | ||||
| Current Integral Gain | Read and write | ||||
| Max. + Torque Curr. | % | Read and write | |||
| Max. - Torque Curr. | % | Read and write | |||
| Min. Torque Curr. | % | Read and write | |||
| Flux Proport. Gain | Read and write | ||||
| Flux Integral Gain | Read and write | ||||
| Minimum Flux | % | Read and write | |||
| Rated Flux | % | Read and write | |||
| Iq* After I/f | % | Read and write | |||
| Magnetization Mode | Read and write | ||||
| Speed for I/F Activ. | rpm | Read and write | |||
| Current in I/F Mode | Read and write | ||||
| DC Link Regul. Mode | Read and write | ||||
| DC Link Regul. Level | V | Read and write | |||
| DC Link Prop. Gain | Read and write | ||||
| DC Link Integral Gain | Read and write | ||||
| Voltage Proport. Gain | Read and write | ||||
| Voltage Integral Gain | Read and write | ||||
| Max. Output Voltage P0190 | V | Read and write | |||
| Encoder Zero Search | Read and write | ||||
| Status Encoder Zero Search | Read | ||||
| Day of the Week | Read and write | ||||
| Day | Read and write | ||||
| Month | Read and write | ||||
| Year | Read and write | ||||
| Hour | Read and write | ||||
| Minutes | Read and write | ||||
| Seconds | Read and write | ||||
| Password | Read and write | ||||
| Language | Read and write | ||||
| Type of Control | Read and write | ||||
| Special Function Sel. | Read and write | ||||
| Load/Save Parameters | Read and write | ||||
| Read Parameter Sel. 1 | Read and write | ||||
| Read Parameter Sel. 2 | Read and write | ||||
| Read Parameter Sel. 3 | Read and write | ||||
| Ref. Scale Factor | Read and write | ||||
| Ref. Eng. Unit 1 | Read and write | ||||
| Ref. Eng. Unit 2 | Read and write | ||||
| Ref. Eng. Unit 3 | Read and write | ||||
| Ref. Decimal Point | Read and write | ||||
| Full Scale Read 1 | % | Read and write | |||
| Full Scale Read 2 | % | Read and write | |||
| Full Scale Read 3 | % | Read and write | |||
| HMI Display Contrast | Read and write | ||||
| Zero Speed Disable | Read and write | ||||
| Zero Speed Dis. Out | Read and write | ||||
| Zero Speed Time | s | Read and write | |||
| LOC/REM Selection Src | Read and write | ||||
| LOC Reference Sel. | Read and write | ||||
| REM Reference Sel. | Read and write | ||||
| LOC FWD/REV Selection | Read and write | ||||
| LOC Run/Stop Sel. | Read and write | ||||
| LOC JOG Selection | Read and write | ||||
| REM FWD/REV Sel. | Read and write | ||||
| REM Run/Stop Sel. | Read and write | ||||
| REM JOG Selection | Read and write | ||||
| Stop Mode Selection | Read and write | ||||
| Dead Zone (AIs) | Read and write | ||||
| AI1 Signal Function | Read and write | ||||
| AI1 Gain | Read and write | ||||
| AI1 Signal Type | Read and write | ||||
| AI1 Offset | % | Read and write | |||
| AI1 Filter | s | Read and write | |||
| AI2 Signal Function | Read and write | ||||
| AI2 Gain | Read and write | ||||
| AI2 Signal Type | Read and write | ||||
| AI2 Offset | % | Read and write | |||
| AI2 Filter | s | Read and write | |||
| AI3 Signal Function | Read and write | ||||
| AI3 Gain | Read and write | ||||
| AI3 Signal Type | Read and write | ||||
| AI3 Offset | % | Read and write | |||
| AI3 Filter | s | Read and write | |||
| AI4 Signal Function | Read and write | ||||
| AI4 Gain | Read and write | ||||
| AI4 Signal Type | Read and write | ||||
| AI4 Offset | % | Read and write | |||
| AI4 Filter | s | Read and write | |||
| AO1 Function | Read and write | ||||
| AO1 Gain | Read and write | ||||
| AO1 Signal Type | Read and write | ||||
| AO2 Function | Read and write | ||||
| AO2 Gain | Read and write | ||||
| AO2 Signal Type | Read and write | ||||
| AO3 Function | Read and write | ||||
| AO3 Gain | Read and write | ||||
| AO3 Signal Type | Read and write | ||||
| AO4 Function | Read and write | ||||
| AO4 Gain | Read and write | ||||
| AO4 Signal Type | Read and write | ||||
| DI1 Function | Read and write | ||||
| DI2 Function | Read and write | ||||
| DI3 Function | Read and write | ||||
| DI4 Function | Read and write | ||||
| DI5 Function | Read and write | ||||
| DI6 Function | Read and write | ||||
| DI7 Function | Read and write | ||||
| DI8 Function | Read and write | ||||
| Filter for Torque Current - Iq | s | Read and write | |||
| Hysteresis for Torque Current Iq | % | Read and write | |||
| DO1 Function (RL1) | Read and write | ||||
| DO2 Function (RL2) | Read and write | ||||
| DO3 Function (RL3) | Read and write | ||||
| DO4 Function | Read and write | ||||
| DO5 Function | Read and write | ||||
| Fx Frequency | Hz | Read and write | |||
| Fx Hysteresis | Hz | Read and write | |||
| DO2 ON Time | s | Read and write | |||
| DO2 OFF Time | s | Read and write | |||
| DO3 ON Time | s | Read and write | |||
| DO3 OFF Time | s | Read and write | |||
| Nx/Ny Hysteresis | rpm | Read and write | |||
| Nx Speed | rpm | Read and write | |||
| Ny Speed | rpm | Read and write | |||
| Ix Current | A | Read and write | |||
| Zero Speed Zone | rpm | Read and write | |||
| N = N* Band | rpm | Read and write | |||
| Tx Torque | % | Read and write | |||
| Hx Time | h | Read and write | |||
| ND/HD VFD Rated Curr. | Read | ||||
| Line Rated Voltage | Read and write | ||||
| Switching Frequency | Read and write | ||||
| Application | Read and write | ||||
| DC-Braking Start Time | s | Read and write | |||
| DC-Braking Stop Time | s | Read and write | |||
| DC-Braking Speed | rpm | Read and write | |||
| DC-Braking Voltage | % | Read and write | |||
| Skip Speed 1 | rpm | Read and write | |||
| Skip Speed 2 | rpm | Read and write | |||
| Skip Speed 3 | rpm | Read and write | |||
| Skip Band | rpm | Read and write | |||
| Serial Address | Read and write | ||||
| Serial Baud Rate | Read and write | ||||
| Serial Bytes Config. | Read and write | ||||
| Serial Protocol | Read and write | ||||
| Comm. Error Action | Read and write | ||||
| Serial Watchdog | s | Read and write | |||
| Serial Interf. Status | Read | ||||
| Oriented Start-up | Read and write | ||||
| Copy Function MemCard | Read and write | ||||
| Copy Function HMI | Read and write | ||||
| FlyStart/Ride-Through | Read and write | ||||
| DC Link Power Loss | V | Read and write | |||
| DC Link Ride-Through | V | Read and write | |||
| DC Link Power Back | V | Read and write | |||
| Ride-Through P Gain | Read and write | ||||
| Ride-Through I Gain | Read and write | ||||
| F.S. Current Ramp I/f | s | Read and write | |||
| Flying Start Filter | s | Read and write | |||
| Frequency Ramp F.S. | Read and write | ||||
| Voltage Ramp | s | Read and write | |||
| Dead Time | s | Read and write | |||
| Auto-Reset Time | s | Read and write | |||
| V/f Outp. Volt. Comp. | Read and write | ||||
| Motor Unbal.Curr.Conf | Read and write | ||||
| Ground Fault Config. | Read and write | ||||
| Current Lim. Conf. | Read and write | ||||
| Motor Overload Conf. | Read and write | ||||
| Ixt Alarm Level | % | Read and write | |||
| IGBTs Overload Conf. | Read and write | ||||
| Motor Overtemp. Conf. | Read and write | ||||
| Fan Control Config. | Read and write | ||||
| IGBTs/Air Overtmp.Cfg | Read and write | ||||
| Fan Speed Fault Config. | Read and write | ||||
| F185 Fault Configuration | Read and write | ||||
| Dead Time Compens. | Read and write | ||||
| Line Phase Loss Time | s | Read and write | |||
| Encoder Fault Config. | Read and write | ||||
| Motor Current Stabil. | Read and write | ||||
| Temp. Imb. Conf. | Read and write | ||||
| Stop Engine Fail Time | s | Read and write | |||
| DC-Braking Curr Sless | % | Read and write | |||
| PTC1 Type Sensor | Read and write | ||||
| Sensor 1 F/A Conf. | Read and write | ||||
| Temper. F/A Sensor 1 | °C | Read and write | |||
| PTC2 Type Sensor | Read and write | ||||
| Sensor 2 F/A Conf. | Read and write | ||||
| Temper. F/A Sensor 2 | °C | Read and write | |||
| PTC3 Type Sensor | Read and write | ||||
| Sensor 3 F/A Conf. | Read and write | ||||
| Temper. F/A Sensor 3 | °C | Read and write | |||
| PTC4 Type Sensor | Read and write | ||||
| Sensor 4 F/A Conf. | Read and write | ||||
| Temper. F/A Sensor 4 | °C | Read and write | |||
| PTC5 Type Sensor | Read and write | ||||
| Sensor 5 F/A Conf. | Read and write | ||||
| Temper. F/A Sensor 5 | °C | Read and write | |||
| Temperature Sensor 1 | °C | Read | |||
| Temperature Sensor 2 | °C | Read | |||
| Temperature Sensor 3 | °C | Read | |||
| Temperature Sensor 4 | °C | Read | |||
| Temperature Sensor 5 | °C | Read | |||
| Highest Temp. Sens. | °C | Read | |||
| Cable Alarm Temper. | °C | Read and write | |||
| Slip Compensation P0397 | Read and write | ||||
| Motor Service Factor | Read and write | ||||
| Motor Rated Eff. | % | Read and write | |||
| Motor Rated Voltage | V | Read and write | |||
| Motor Rated Current | A | Read and write | |||
| Motor Rated Speed | rpm | Read and write | |||
| Motor Rated Frequency | Hz | Read and write | |||
| Motor Rated Power | Read and write | ||||
| Encoder Pulses Number | Read and write | ||||
| Motor Ventilation | Read and write | ||||
| Motor Rated Power Fac | Read and write | ||||
| Run Self-Tuning | Read and write | ||||
| Stator Resistance | Ω | Read and write | |||
| Magnetization Current | A | Read and write | |||
| Leakage Inductance | Read and write | ||||
| Tr Time Constant | s | Read and write | |||
| Tm Time Constant | s | Read and write | |||
| Motor Magnetization Time | s | Read and write | |||
| Type PM | Read and write | ||||
| Pole Number | Read and write | ||||
| Lq Inductance | Read and write | ||||
| Ld Inductance | Read and write | ||||
| Ke Constant | Read and write | ||||
| Iq Prop. Gain | Read and write | ||||
| Iq Integral Gain | Read and write | ||||
| Id Prop. Gain | Read and write | ||||
| Id Integral Gain | Read and write | ||||
| Inductance Lq CT | Read and write | ||||
| Inductance Ld CT | Read and write | ||||
| Constant Ke CT | Read and write | ||||
| PID Proportional Gain | Read and write | ||||
| PID Integral Gain | Read and write | ||||
| PID Differential Gain | Read and write | ||||
| PID Ramp Time | s | Read and write | |||
| PID Feedback Sel. | Read and write | ||||
| Keypad PID Setpoint | % | Read and write | |||
| PID Action Type | Read and write | ||||
| Proc. V. Scale Factor | Read and write | ||||
| Proc.V. Decimal Point | Read and write | ||||
| Proc. V. Eng. Unit 1 | Read and write | ||||
| Proc. V. Eng. Unit 2 | Read and write | ||||
| Proc. V. Eng. Unit 3 | Read and write | ||||
| PVx Value | % | Read and write | |||
| PVy Value | % | Read and write | |||
| Wake Up Band | % | Read and write | |||
| P0525 Autom. Setting | Read and write | ||||
| Hysteresis VPx/VPy | % | Read and write | |||
| Trigger Signal Source | Read and write | ||||
| Trigger Level | % | Read and write | |||
| Trigger Condition | Read and write | ||||
| Trace Sampling Period | Read and write | ||||
| Trace Pre-Trigger | % | Read and write | |||
| Trace Max. Memory | % | Read and write | |||
| Trace Avail. Memory | % | Read | |||
| Trace Channel 1 (CH1) | Read and write | ||||
| Trace Channel 2 (CH2) | Read and write | ||||
| Trace Channel 3 (CH3) | Read and write | ||||
| Trace Channel 4 (CH4) | Read and write | ||||
| Start Trace Function | Read and write | ||||
| Trace Trig. Day/Month | Read | ||||
| Trace Trig. Year | Read | ||||
| Trace Trig. Time | Read | ||||
| Trace Trig. Seconds | Read | ||||
| Trace Function Status | Read | ||||
| Energy Saving Config. | Read and write | ||||
| Cos Phi Reference | Read and write | ||||
| Energy Sav. Max. Torq | % | Read and write | |||
| Energy Sav. Min. Volt/Flux | % | Read and write | |||
| Energy Sav. Min. Sp. | rpm | Read and write | |||
| Energy Sav. Hysteresis | % | Read and write | |||
| Firmware Update | Read and write | ||||
| Firmware Revision | Read | ||||
| Revision of the PLD | Read | ||||
| CO/DN/DP Control | Read | ||||
| CO/DN/DP Speed Ref | Read | ||||
| Anybus-CC Control | Read | ||||
| Anybus-CC Speed Ref. | Read | ||||
| Operating Mode States | Read | ||||
| DOx Value | Read and write | ||||
| AOx Value 1 | Read and write | ||||
| AOx Value 2 | Read and write | ||||
| AOx Value 3 | Read and write | ||||
| AOx Value 4 | Read and write | ||||
| CAN Protocol | Read and write | ||||
| CAN Address | Read and write | ||||
| CAN Baud Rate | Read and write | ||||
| Bus Off Reset | Read and write | ||||
| CAN Controller Status | Read | ||||
| RX CAN Telegrams | Read | ||||
| TX CAN Telegrams | Read | ||||
| Bus Off Counter | Read | ||||
| CAN Lost Messages | Read | ||||
| DNet I/O instances | Read and write | ||||
| DNet Read Word #3 | Read and write | ||||
| DNet Read Word #4 | Read and write | ||||
| DNet Read Word #5 | Read and write | ||||
| DNet Read Word #6 | Read and write | ||||
| DNet Write Word #3 | Read and write | ||||
| DNet Write Word #4 | Read and write | ||||
| DNet Write Word #5 | Read and write | ||||
| DNet Write Word #6 | Read and write | ||||
| DNet Network Status | Read | ||||
| DNet Master Status | Read | ||||
| CANopen Comm. Status | Read | ||||
| CANopen Node State | Read | ||||
| Anybus Identification | Read | ||||
| Anybus Comm. Status | Read | ||||
| Anybus Address | Read and write | ||||
| Anybus Baud Rate | Read and write | ||||
| Anybus I/O Words | Read and write | ||||
| Anybus Read Word #3 | Read and write | ||||
| Anybus Read Word #4 | Read and write | ||||
| Anybus Read Word #5 | Read and write | ||||
| Anybus Read Word #6 | Read and write | ||||
| Anybus Read Word #7 | Read and write | ||||
| Anybus Read Word #8 | Read and write | ||||
| Anybus Write Word #3 | Read and write | ||||
| Anybus Write Word #4 | Read and write | ||||
| Anybus Write Word #5 | Read and write | ||||
| Anybus Write Word #6 | Read and write | ||||
| Anybus Write Word #7 | Read and write | ||||
| Anybus Write Word #8 | Read and write | ||||
| Profibus Comm. Status | Read | ||||
| Profibus Data Profile | Read and write | ||||
| Profibus Reading Word #3 | Read and write | ||||
| Profibus Reading Word #4 | Read and write | ||||
| Profibus Reading Word #5 | Read and write | ||||
| Profibus Reading Word #6 | Read and write | ||||
| Profibus Reading Word #7 | Read and write | ||||
| Profibus Reading Word #8 | Read and write | ||||
| Profibus Reading Word #9 | Read and write | ||||
| Profibus Reading Word#10 | Read and write | ||||
| Profibus Writing Word#3 | Read and write | ||||
| Profibus Writing Word#4 | Read and write | ||||
| Profibus Writing Word#5 | Read and write | ||||
| Profibus Writing Word#6 | Read and write | ||||
| Profibus Writing Word#7 | Read and write | ||||
| Profibus Writing Word#8 | Read and write | ||||
| Profibus Writing Word#9 | Read and write | ||||
| Profibus Writing Word#10 | Read and write | ||||
| PROFIdrive Output I | Read and write | ||||
| PROFIdrive Active P | Read and write | ||||
| PROFIdrive Torque Val | Read and write | ||||
| PROFIdrive SW NAMUR | Read and write | ||||
| Delay Update I/O | Read and write | ||||
| Phase U Book 1 Temperature | °C | Read | |||
| Phase V Book 1 Temperature | °C | Read | |||
| Phase W Book 1 Temperature | °C | Read | |||
| Phase U Book 2 Temperature | °C | Read | |||
| Phase V Book 2 Temperature | °C | Read | |||
| Phase W Book 2 Temperature | °C | Read | |||
| Phase U Book 3 Temperature | °C | Read | |||
| Phase V Book 3 Temperature | °C | Read | |||
| Phase W Book 3 Temperature | °C | Read | |||
| Phase U Book 4 Temperature | °C | Read | |||
| Phase V Book 4 Temperature | °C | Read | |||
| Phase W Book 4 Temperature | °C | Read | |||
| Phase U Book 5 Temperature | °C | Read | |||
| Phase V Book 5 Temperature | °C | Read | |||
| Phase W Book 5 Temperature | °C | Read | |||
| Current U-B1/IGBT U1 | A | Read | |||
| Current V-B1/IGBT V1 | A | Read | |||
| Current W-B1/IGBT W1 | A | Read | |||
| Current U-B2/IGBT U2 | A | Read | |||
| Current V-B2/IGBT V2 | A | Read | |||
| Current W-B2/IGBT W2 | A | Read | |||
| Current U-B3/IGBT U3 | A | Read | |||
| Current V-B3/IGBT V3 | A | Read | |||
| Current W-B3/IGBT W3 | A | Read | |||
| Current U-B4/IGBT U4 | A | Read | |||
| Current V-B4/IGBT V4 | A | Read | |||
| Current W-B4/IGBT W4 | A | Read | |||
| Current U-B5/IGBT U5 | A | Read | |||
| Current V-B5/IGBT V5 | A | Read | |||
| Current W-B5/IGBT W5 | A | Read | |||
| DIM1 Function | Read and write | ||||
| DIM2 Function | Read and write | ||||
| DIM1 DIM2 Status | Read | ||||
| Ret. Temp. Phase R | °C | Read | |||
| Ret. Temp. Phase S | °C | Read | |||
| Ret. Temp. Phase T | °C | Read | |||
| Anybus Status | Read and write | ||||
| Eth:Baud rate | Read and write | ||||
| Eth:ModbusTCP timeout | Read and write | ||||
| Eth:IP Address Config | Read and write | ||||
| Eth:IP Address 1 | Read and write | ||||
| Eth:IP Address 2 | Read and write | ||||
| Eth:IP Address 3 | Read and write | ||||
| Eth:IP Address 4 | Read and write | ||||
| CIDR | Read and write | ||||
| Gateway 1 | Read and write | ||||
| Gateway 2 | Read and write | ||||
| Gateway 3 | Read and write | ||||
| Gateway 4 | Read and write | ||||
| Station Name | Read and write | ||||
| Compatible mode | Read and write | ||||
| Profibus Address | Read and write | ||||
| Profibus Teleg. Sel. | Read and write | ||||
| Fault Message Counter | Read | ||||
| Fault Number | Read | ||||
| Profibus Baud Rate | Read | ||||
| Drive Unit Ident. | Read | ||||
| Profile Ident. Number | Read | ||||
| Control Word PROFIdrive | Read | ||||
| Status Word PROFIdrive | Read | ||||
| SoftPLC Status | Read | ||||
| SoftPLC Command | Read and write | ||||
| Scan Cycle Time | ms | Read | |||
| SoftPLC Supervision | Read and write | ||||
| SoftPLC Parameter 1 | Read and write | ||||
| SoftPLC Parameter 2 | Read and write | ||||
| SoftPLC Parameter 3 | Read and write | ||||
| SoftPLC Parameter 4 | Read and write | ||||
| SoftPLC Parameter 5 | Read and write | ||||
| SoftPLC Parameter 6 | Read and write | ||||
| SoftPLC Parameter 7 | Read and write | ||||
| SoftPLC Parameter 8 | Read and write | ||||
| SoftPLC Parameter 9 | Read and write | ||||
| SoftPLC Parameter 10 | Read and write | ||||
| SoftPLC Parameter 11 | Read and write | ||||
| SoftPLC Parameter 12 | Read and write | ||||
| SoftPLC Parameter 13 | Read and write | ||||
| SoftPLC Parameter 14 | Read and write | ||||
| SoftPLC Parameter 15 | Read and write | ||||
| SoftPLC Parameter 16 | Read and write | ||||
| SoftPLC Parameter 17 | Read and write | ||||
| SoftPLC Parameter 18 | Read and write | ||||
| SoftPLC Parameter 19 | Read and write | ||||
| SoftPLC Parameter 20 | Read and write | ||||
| SoftPLC Parameter 21 | Read and write | ||||
| SoftPLC Parameter 22 | Read and write | ||||
| SoftPLC Parameter 23 | Read and write | ||||
| SoftPLC Parameter 24 | Read and write | ||||
| SoftPLC Parameter 25 | Read and write | ||||
| SoftPLC Parameter 26 | Read and write | ||||
| SoftPLC Parameter 27 | Read and write | ||||
| SoftPLC Parameter 28 | Read and write | ||||
| SoftPLC Parameter 29 | Read and write | ||||
| SoftPLC Parameter 30 | Read and write | ||||
| SoftPLC Parameter 31 | Read and write | ||||
| SoftPLC Parameter 32 | Read and write | ||||
| SoftPLC Parameter 33 | Read and write | ||||
| SoftPLC Parameter 34 | Read and write | ||||
| SoftPLC Parameter 35 | Read and write | ||||
| SoftPLC Parameter 36 | Read and write | ||||
| SoftPLC Parameter 37 | Read and write | ||||
| SoftPLC Parameter 38 | Read and write | ||||
| SoftPLC Parameter 39 | Read and write | ||||
| SoftPLC Parameter 40 | Read and write | ||||
| SoftPLC Parameter 41 | Read and write | ||||
| SoftPLC Parameter 42 | Read and write | ||||
| SoftPLC Parameter 43 | Read and write | ||||
| SoftPLC Parameter 44 | Read and write | ||||
| SoftPLC Parameter 45 | Read and write | ||||
| SoftPLC Parameter 46 | Read and write | ||||
| SoftPLC Parameter 47 | Read and write | ||||
| SoftPLC Parameter 48 | Read and write | ||||
| SoftPLC Parameter 49 | Read and write | ||||
| SoftPLC Parameter 50 | Read and write |
Loading registers…

Send your device list
If a device is not in the library yet, we build the template for free as soon as we have the register data.
Use cases
- Show motor speed, current, output power and DC link voltage of every drive on one dashboard.
- Send an alarm when the present fault code is not zero, or when the heatsink temperature passes a threshold.
- Keep a year of current and power history to see when a pump or fan runs heavier than normal.
- Change the speed reference or the PID setpoint of a pump from ModbusCloud without going to site.
- Compare operating hours, enabled time and output energy across drives to plan maintenance.
Installation
Fit the RS485-01 module in the drive and connect terminal 1 (A) and terminal 2 (B) to RS485 A and B of the ModbusCloud Gateway. Switch on termination (S1) on the last device.
On the drive keypad set P0308 to the Modbus address, P0310 to the baud rate, P0311 to the byte format and P0312 to 2 (Modbus RTU).
If ModbusCloud should control the drive, set the command and reference sources in P0220 to P0228 to Serial/USB.
In ModbusCloud add a Modbus device on the Gateway with the same address and serial settings and import this template.
Check that Motor Speed, Motor Current and DC Link Voltage show plausible values with the drive powered.
Things to watch for
The drive does not answer on the bus. What should I check?
Check that the RS485 module is fitted and P0316 shows 1 (active). Address, baud rate and byte format in P0308, P0310 and P0311 must match the settings in ModbusCloud; firmware V6.0X ships with 8 data bits, no parity and 2 stop bits. If it still stays silent, swap A and B and check the termination switch.
Why does Motor Current show ten times the real value?
The drive sends values as whole numbers without the decimal point, so 3.5 A arrives as 35. The template applies the scale from the parameter list. Parameters whose range is a multiple of the rated current, such as the overload currents, are read with scale 1 because their resolution is not stated.
How do I start the motor and set the speed?
Set the command and reference sources (P0220 to P0228) to Serial/USB. Then write the speed reference, where 8192 equals the synchronous motor speed, and write the serial control word with bit 0 (ramp enable), bit 1 (general enable) and bit 4 (remote) set. Test with the motor uncoupled first.
Some parameters refuse a write. Why?
Parameters marked as configuration parameters can only be changed with the motor stopped, and read only parameters never accept a write. Values outside the range in the comment are rejected as well. Change one setting at a time and read it back to confirm it took effect.
Can I connect several CFW11 drives to one Gateway?
Yes. Give each drive its own address in P0308 and use the same baud rate and byte format on all of them. Wire the bus as one line from drive to drive and enable termination only on the two ends.
More WEG templates
Want to see how it works?








