Alpha Innotec Heating & Cooling LUX 2.1 SHI

Use cases

• Monitor real-time power consumption and room temperature of an Alpha Innotec heat pump on a cloud dashboard.
• Create an alert when domestic hot water status indicates a fault or temperature drop below the expected range.
• Remotely block or unblock heating and cooling circuits during maintenance or seasonal changeover.
• Adjust the power consumption limitation register to comply with grid operator curtailment requests under paragraph 14a EnWG.
• Integrate PV surplus data with heating level controls to maximize self-consumption of solar energy.
• Track long-term thermal performance by logging setpoints, room temperatures, and power consumption over time.

Installation

1. 1Connect the Alpha Innotec heat pump to the local network via its built-in Ethernet port on the Luxtronik 2.1 controller.
2. 2Activate the Smart Home Interface in the Luxtronik 2.1 settings menu, following pages 45 to 47 of the official manual (83055400pUK_Lux_21_Teil_2.pdf).
3. 3Assign a static IP address to the heat pump or create a DHCP reservation so the address does not change.
4. 4Connect your ModbusCloud gateway (MCG or MLP series) to the same local network and ensure it can reach the heat pump's IP address on the Modbus TCP port.
5. 5Import the Alpha Innotec Heating and Cooling LUX 2.1 SHI template in the ModbusCloud portal and enter the heat pump's IP address.
6. 6Verify communication by checking that live values for RBE temperature and power consumption appear on the ModbusCloud dashboard.

Things to watch for

01

Do I need an external Modbus RTU to TCP converter for this heat pump?

No. The Luxtronik 2.1 controller has a built-in Ethernet port and supports Modbus TCP natively through the Smart Home Interface. No additional converter is required.

02

The gateway cannot connect to the heat pump. What should I check?

Verify that the Smart Home Interface is activated in the Luxtronik 2.1 controller (manual pages 45 to 47). Confirm the heat pump has a valid IP address and that no firewall or VLAN is blocking traffic between the gateway and the heat pump.

03

Which Alpha Innotec models are supported by this template?

All models equipped with the Luxtronik 2.1 controller are supported. This includes the Hybrox, LWAV, LWA, LWP, Paros, LWCV, LWV, SWCV, WZSV, SW, and SWC series.

04

Can I write control values such as heating mode while the heat pump is running?

Yes. The Smart Home Interface allows writing to control registers during operation. Changes to heating mode, DHW level, or power limitation take effect immediately on the controller.

Registers (14)

4 read / 10 write

More Alpha Innotec templates

Alpha Innotec Heating & Cooling LUX 2.0

Alpha Innotec

Modbus TCP

Control Alpha Innotec heatpumps via Modbus TCP for heating, cooling, and hot water management.

15 registers137

Alpha Innotec Heating & Cooling Split

Alpha Innotec

Modbus TCP

Monitors and controls Alpha Innotec split heat pumps via Modbus TCP.

13 registers44

More TCP templates

Algodue Energy meter UEM80-2D E

Algodue Elettronica S.r.l.

Modbus TCP

Measures single-phase energy consumption and production via Modbus TCP.

12 registers46

Sigenergy SigenStore EC (grid)

Sigenergy

Modbus TCP

5 registers1

Fronius GEN24

Fronius

Modbus TCP

Monitors and controls Fronius GEN24 inverters and PV batteries via SunSpec Modbus TCP

0 registers762

HUAWEI SUN2000 Inverter & LUNA2000 battery

Huawei

Modbus TCP

Monitors HUAWEI SUN2000 inverter, LUNA2000 battery, and Smart Power Sensor via Modbus TCP.

4 registers1248

NIBE Nibe S-Series (SG Ready)

NIBE

Modbus TCP

5 registers1

Fronius - Modbus TCP

Fronius

Modbus TCP

Monitors Fronius Symo and Primo inverters via Modbus TCP

15 registers597