
Schneider Electric EVlink Pro AC
AC charging station with charging state, power, energy and a remote current setpoint.
The Schneider Electric EVlink Pro AC is an AC charging station that charges electric cars at offices, car parks and fleet sites. This Modbus TCP template reads charging state, OCPP status, power, current, energy and errors, and lets you set the charging current and send start and stop commands from ModbusCloud.
- Protocol
- Modbus TCP
- Connection
- Ethernet, Modbus TCP
- Registers
- 50, read and write
- Brand
- Schneider Electric
- Key readings
- Charging state · OCPP status · Current per phase · Active power · Active energy · Session energy · Session charging time
- Available commands
- Current setpoint · Charge command · Lifebit
- Compatible models
- EVlink Pro AC · Schneider Electric EVlink Pro AC with T2S socket · Schneider Electric EVlink Pro AC with attached cable · Schneider Electric EVlink Pro AC with T2S and domestic socket
- Last updated
Registers (50)
50 read, 3 write
| Name | Unit | Access | Address (Hidden until you enter your email) | Function (hidden) | Type (hidden) |
|---|---|---|---|---|---|
| Current Phase 1 | A | Read | 2999 | FC03 | float32 |
| Current Phase 2 | A | Read | 3001 | FC03 | float32 |
| Current Phase 3 | A | Read | 3003 | FC03 | float32 |
| Current Average | A | Read | 3009 | FC03 | float32 |
| Voltage Phase 1 | V | Read | 3027 | FC03 | float32 |
| Voltage Phase 2 | V | Read | |||
| Voltage Phase 3 | V | Read | |||
| Voltage Average | V | Read | |||
| Active Power Phase 1 | kW | Read | |||
| Active Power Phase 2 | kW | Read | |||
| Active Power Phase 3 | kW | Read | |||
| Active Power Total | kW | Read | |||
| Reactive Power Total | kvar | Read | |||
| Apparent Power Total | kVA | Read | |||
| Power Factor | Read | ||||
| Frequency | Hz | Read | |||
| Active Energy Total | Wh | Read | |||
| Reactive Energy Total | kvarh | Read | |||
| Session Energy | Wh | Read | |||
| EV State | Read | ||||
| OCPP Status | Read | ||||
| EV Presence | Read | ||||
| Last Stop Cause | Read | ||||
| Error Group Bitfield | Read | ||||
| Error Code Bitfield | Read | ||||
| Last Event 0 Code | Read | ||||
| Last Event 0 Start Time | s | Read | |||
| Last Event 0 End Time | s | Read | |||
| Last Event 1 Code | Read | ||||
| Last Event 1 Start Time | s | Read | |||
| Last Event 1 End Time | s | Read | |||
| Last Event 2 Code | Read | ||||
| Last Event 2 Start Time | s | Read | |||
| Last Event 2 End Time | s | Read | |||
| Last Event 3 Code | Read | ||||
| Last Event 3 Start Time | s | Read | |||
| Last Event 3 End Time | s | Read | |||
| Contactor Charging Time | s | Read | |||
| Session Charging Time | s | Read | |||
| Set Point | A | Read and write | |||
| Degraded Set Point Single Phase | A | Read | |||
| Degraded Set Point Three Phase | A | Read | |||
| Lifebit | Read and write | ||||
| Set Command | Read and write | ||||
| Command Status | Read | ||||
| Firmware Major Version | Read | ||||
| Firmware Minor Version | Read | ||||
| Firmware Build Version | Read | ||||
| EVSE Model | Read | ||||
| EVSE Commercial Reference | Read |
Loading registers…

Send your device list
If a device is not in the library yet, we build the template for free as soon as we have the register data.
Use cases
- Show charging state, power and session energy of every charging station on a ModbusCloud dashboard.
- Lower the current setpoint of a charging station from ModbusCloud when the building connection is near its limit.
- Get an email when the OCPP status changes to Faulted or the error bitfield is not zero.
- Keep a year of energy history per charging station to report consumption per car park or tenant.
- Use an automation to switch a charging station unavailable outside office hours.
Installation
Connect the Ethernet port of the charging station to the same network as the ModbusCloud Gateway and give it a fixed IP address.
Enable the Modbus interface with eSetup and set the communication timeout and the degraded setpoints for single and three-phase charging.
In ModbusCloud, add a Modbus TCP device on the Gateway with the IP address of the station, port 502 and unit ID 255, and choose the EVlink Pro AC template.
Check that OCPP status and EV state show plausible values and that current and power rise when a car charges.
Things to watch for
Why does the charging station not answer Modbus requests?
Check that Modbus is enabled in eSetup, that the station and the Gateway are in the same network and that the unit ID is 255. Reading an address that is not in the register list returns an illegal data address exception, so use the template addresses unchanged.
Why does the station fall back to a low charging current?
When the lifebit is active and not refreshed within the communication timeout, the station treats Modbus as lost and applies the degraded setpoint from eSetup. Write the lifebit regularly, or write 2 to switch the lifebit off.
How do I set the charging current from ModbusCloud?
Write the current in amperes, 0 to 32, to the setpoint register. The station applies a change within 15 seconds. The value 99 means no setpoint was set by Modbus. Writing to a station needs remote control enabled for the gateway in ModbusCloud.
Why do some registers return 65535?
Some register ranges are reserved, and reading them returns 0xFFFF. Values that only change during a session, such as EV presence, are updated only when the station is not charging.
More Schneider Electric templates
Want to see how it works?











