E+E Elektronik EE680 - Air Velocity Sensor for Laminar Flow Monitoring

Installation

1. 1Connect the EE680 sensor to the RS-485 terminals (A, B, GND) of your ModbusCloud gateway (MCG or MLP series).
2. 2Verify that the EE680 is configured to communicate at 9600 baud with odd parity (default settings).
3. 3Set a unique Modbus RTU slave address on the EE680 if multiple devices share the same bus.
4. 4Import the E+E Elektronik EE680 template in the ModbusCloud platform and assign it to the connected gateway.
5. 5Confirm that airflow (register 1044) and temperature (register 1002) values appear correctly on your dashboard.

Things to watch for

01

I see zero or incorrect values for airflow and temperature. What should I check?

Both registers (1044 and 1002) use float32 encoding, which spans two consecutive Modbus registers. Verify that the byte order and word order settings in the gateway match the EE680 output. Also confirm that the correct slave address is configured.

02

What baud rate and parity settings does the EE680 use by default?

The default communication settings are 9600 baud with odd parity (1 stop bit). These must match the configuration on your ModbusCloud gateway for successful communication.

03

Can I connect multiple EE680 sensors on the same RS-485 bus?

Yes. Assign a unique Modbus slave address to each EE680 sensor. Then create a separate device entry in ModbusCloud for each address, all using the same EE680 template.

04

How accurate is the airflow reading at very low velocities?

The EE680 is rated for accuracy down to 0.1 m/s (20 ft/min) thanks to its thin film sensing element. Below this threshold, readings may become less reliable.

Registers (2)

2 read / 0 write

More E+E Elektronik templates

E+E Elektronik EE260 - Heated Humidity and Temperature Probe for Meteorology

E+E Elektronik

Modbus RTU

Measures heated humidity and temperature for meteorology applications

4 registers31

E+E Elektronik EE072 - Humidity and Temperature Probe with Digital Interface

E+E Elektronik

Modbus RTU

Measures relative humidity, temperature, and derived humidity parameters for process control.

5 registers26

E+E Elektronik EE800 - CO2, Temperature and Humidity Room Sensor

E+E Elektronik

Modbus RTU

Measures CO2, temperature, humidity and dew point for room climate control

4 registers23

E+E Elektronik EE600 - Differential Pressure Sensor

E+E Elektronik

Modbus RTU

Measures differential air pressure for HVAC and filter monitoring applications.

1 registers21

E+E Elektronik EE671 - HVAC Miniature Air Flow Probe

E+E Elektronik

Modbus RTU

Measures air velocity and temperature for HVAC applications.

2 registers20

EE

E+E Elektronik EE310 - High-end humidity and temperature sensor up to 180 °C

E+E Elektronik

Modbus RTU

Measures humidity and temperature for demanding industrial environments up to 180 °C

5 registers10

More RTU templates

Alnor HRU-P

Alnor Systemy Wentylacji Sp. z o. o.

Modbus RTU

Controls Alnor HRU-P heat recovery ventilation units via Modbus RTU.

49 registers7

Alnor HRU

Alnor Systemy Wentylacji Sp. z o. o.

Modbus RTU

Controls and monitors Alnor heat recovery ventilation units via Modbus RTU.

29 registers13

Wattsonic - Schmachtl Sun Energy Box

Wattsonic

Modbus RTU

Monitors Schmachtl Wattsonic hybrid inverter via Modbus RTU

92 registers72

Heidelberg Wallbox Energy Control

AMPERFIED GmbH

Modbus RTU

Controls and monitors Heidelberg Wallbox Energy Control EV charger via Modbus RTU.

22 registers67

connecdoor.controller

connecdoor

Modbus RTU

Controls and monitors smart door access points via RS485

0 registers53

Belimo Air-Water Actuator Modbus RTU

Belimo

Modbus RTU

Controls communicative damper and valve actuators via Modbus RTU.

20 registers46